Skip to main content
LAYOUTCALCULATOR SCALE 1/16" CAD
2024 IRC Sections R311.7.5.1 (Open Risers) & R311.7.5.3 (Nosings)
2024 IRC Sections R311.7.5.1 (Open Risers) & R311.7.5.3 (Nosings) 10 min read • Updated

Open vs. Closed Stair Risers: 4" Sphere & Nosing Code (2024 IRC Sections R311.7.5.1 (Open Risers) & R311.7.5.3 (Nosings))

Know when open stair risers are legal under 2024 IRC R311.7.5.1, how to restrict riser gaps under 4 inches above 30-inch rise, and 3/4" to 1-1/4" nosings.

Published by LayoutCalculator • Formulas reference published code tables; confirm with your local building official.
Companion 2D SVG CAD Instrument

Need an Instant Scale Blueprint? Launch Stair Stringer Calculator

Generate real-time 1/16" fractional dimensions, framing square marks, and printable workshop sheets.

Open the Stair Stringer Calculator →
Direct Code Summary • 2024 IRC Sections R311.7.5.1 (Open Risers) & R311.7.5.3 (Nosings) SPEC BULLETIN

What Is the Standard Rule for Open vs. Closed Stair Risers?

2024 IRC Sections R311.7.5.1 (Open Risers) & R311.7.5.3 (Nosings): Fully open stair risers with unrestricted gaps are ONLY legal when total vertical stair rise is 30 inches or less above floor or grade (typically 3- or 4-riser low patio steps). Above 30 inches of vertical rise, IRC Section R311.7.5.1 allows open risers ONLY if the clear gap between treads blocks a 4-inch (4.00") diameter sphere (e.g., 3-3/4" thick timber treads or partial toe-kick boards).

LIVE FIELD SOLVER

Interactive Jobsite Verification Instrument

2024 IRC Sections R311.7.5.1 (Open Risers) & R311.7.5.3 (Nosings)
Instant Field Calculation
13 Risers @ 7.38" • 126.0" Run
Adjust inputs above for live takeoff

Key Engineering & Code Takeaways

  • Fully open stair risers with unrestricted gaps are ONLY legal when total vertical stair rise is 30 inches or less above floor or grade (typically 3- or 4-riser low patio steps).
  • Above 30 inches of vertical rise, IRC Section R311.7.5.1 allows open risers ONLY if the clear gap between treads blocks a 4-inch (4.00") diameter sphere (e.g., 3-3/4" thick timber treads or partial toe-kick boards).
  • Under IRC Section R311.7.5.3, solid-riser stairs with tread depths under 11 inches (10.00" to 10.99" unit run) MUST have a 3/4-inch to 1-1/4 inch projecting nosing!
  • Treads measuring 11.00 inches or deeper—or stairs built with open risers—are legally exempt from the 3/4" nosing requirement, making modern mitered "waterfall" hardwood stairs 100% code-compliant at ≥11" run!

Part of our Framing & Stairs series; start with 2024 IRC R311.7 Stair Code. Related: How to Lay Out 2x12 Stair Stringers with a Framing Square, Drop-Mount vs. Flush-Mount Stair Stringers & Ledger Hardware, Stairwell Opening Length Formula for 6'-8" IRC Headroom.

2024 IRC R311.7.5 Open-Riser Sphere & Solid-Riser Nosing Compliance Matrix

← Swipe table horizontally → 2024 IRC Sections R311.7.5.1 (Open Risers) & R311.7.5.3 (Nosings)
2024 IRC R311.7.5 Open-Riser Sphere & Solid-Riser Nosing Compliance Matrix (2024 IRC Sections R311.7.5.1 (Open Risers) & R311.7.5.3 (Nosings))
Stair Style & ElevationClear Riser Opening LimitUnit Run (Nosing-to-Nosing)Required Nosing ProjectionLeading Edge Radius / Bevel
Low Patio Steps (≤ 30" Total Rise) Unlimited (Full open legal!) 10.00" Min 0" Required (Open riser exc.) Max 9/16" radius
Deck Stairs (over 30" Rise, Partial Riser) Under 4.00" Sphere! 10.50" – 11.25" (2 deck bds) 0" if open / 3/4"–1-1/4" if under 11" Max 9/16" radius
Floating Mono-Stringer (3-7/8" Oak) 3.62" Gap @ 7.5" Rise (PASS!) 10.50" – 11.00" 0" Required (Open riser exc.) Max 9/16" radius
Traditional Closed Riser (under 11" Run) 0" (Solid 1x8 riser face) 10.00" to 10.99" 3/4" to 1-1/4" MANDATORY! Max 9/16" rad; ≤ 3/8" variance
Deep Closed Riser (≥ 11.00" Run) 0" (Solid riser / mitered) 11.00" or Deeper! 0" Required (Waterfall legal!) Crisp eased edge ≤ 9/16" rad
30° Angled Sloped Solid Riser 0" (Flush modern kick) 10.00" to 10.99" 0" Overhang if sloped ≤ 30° IRC R311.7.5.3 bevel rule

1. The 30-Inch Cutoff: Why Bare 2x12 Open Risers Fail Deck Inspections

Every week across the United States, DIYers and deck contractors screw bare 2x12 (1-1/2" thick) or twin 5/4×6 (1" thick) treads onto notched 2x12 stringers leading 6 feet down to the backyard—leaving 6.00" to 6.50" of wide-open air between every step—and get red-tagged by the municipal inspector! Read 2024 IRC Section R311.7.5.1 word-for-word: "At open risers, openings located more than 30 inches as measured vertically to the floor or grade below shall not permit the passage of a 4-inch-diameter (102 mm) sphere."

Only low porch or patio stairs sitting 30 inches or less vertically off grade (typically 4 risers × 7.25" = 29.00") can leave risers completely open! Once your staircase climbs above 30 inches vertically, you have three proven, code-legal methods to pass the 4-inch riser sphere check without trapping rotting wet leaves on exterior decks or ruining modern floating interior stairs:

  • Option A — Exterior Deck Partial Riser ("Drain-Gap" Toe-Kick Board): Instead of sealing a full 1x8 riser tight against the lower tread (which traps wet snow and rots out stringer notches!), screw a 1x6 (5-1/2" actual) or ripped 2x6 (4-1/2") pressure-treated/PVC fascia strip onto the vertical riser cut leaving a 1/2" to 1-1/2" drainage gap at the bottom (under 4.00" sphere above AND under 4.00" drainage slot below!).
  • Option B — Floating Mono-Stringer Heavy Timber Treads: On architectural single-steel-spine interior stairs with 7.50" unit rise, fabricate 3-3/4" to 4-inch thick solid white oak or laminated box treads: 7.50" unit rise − 3.75" tread thickness = 3.75 inches clear vertical gap—passing under 4.00" sphere with zero riser board!
  • Option C — Mid-Gap Horizontal Stainless Riser Rod: Drill a single 1/2-inch stainless steel rod or flat bar halfway up the 6" riser opening (2.75" clear gap above and below!).

2. Stringer Plumb-Cut Math: Accounting for 3/4-Inch Closed Riser Boards!

When switching from open risers to full 3/4-inch (1x8 pine, oak, or white PVC) closed riser face boards, novice carpenters routinely nail the 3/4" riser boards straight onto the front of the stringers except at the top ledger—pushing every step forward 3/4" so the top tread winds up 3/4" deeper than the rest (violating the 3/8-inch tread uniformity limit under IRC R311.7.5.2!) OR leaving the bottom step 3/4" out past the floor line! Execute this exact Riser-First Stringer Adjustment alongside our Stair Stringer Layout & IRC Code Calculator:

  • Rule 1 (Install Risers BEFORE Treads): Nail/adhesive-screw the 3/4" vertical riser boards across the plumb cuts of the stringers first, then tuck the rear edge of each horizontal tread tightly underneath (or tight against) the riser board so squeaks cannot develop and water sheds over the seam!
  • Rule 2 (Rip 3/4" Off ONLY the Top Ledger Backing—or Pad the Ledger!): If you nail 3/4" riser boards onto every vertical plumb cut on the stringer AND mount a matching 3/4" finished riser face directly onto the upper rim-joist header (above the top stringer step!), then every single step shifts forward uniformly by 3/4 inch—preserving 100.0% identical 10.50" nosing-to-nosing unit run across all steps with zero saw modifications to the stringer notches! (Only if the top header already sits flush with a finished plaster wall that cannot take a 3/4" riser board do you rip 3/4" off the back plumb hanger cut of the stringer so the top step stays equal!).

3. The IRC R311.7.5.3 Nosing Rule & Modern Waterfall Staircase Secret (≥11" Run!)

Look closely at 2024 IRC Section R311.7.5.3 (Nosings), because it contains the single greatest architectural loophole for modern minimalist custom homes: on stairs with solid risers, a leading-edge nosing projecting 3/4 inch (19 mm) minimum to 1-1/4 inches (32 mm) maximum is mandatory ONLY when tread depth (unit run) is less than 11 inches (10.00" to 10.99")! Furthermore, nosing projection cannot vary by more than 3/8 inch across the flight, and the curve radius at the leading edge cannot exceed 9/16 inch (14.3 mm).

Why do custom architects ask for zero-overhang "waterfall" mitered white oak or microcement stairs where treads and risers meet at crisp 90-degree flush corners? Check IRC Section R311.7.5.3 Exception 1: a nosing projection is not required where the tread depth is not less than 11 inches (279 mm)! Simply setting your framing square unit run to 11.00 inches (or 11-1/4") in our Stair Stringer Layout & IRC Code Calculator makes flush, zero-nosing waterfall stairs 100% legal under the 2024 IRC! Alternatively, tilting solid risers backward at up to a 30-degree undercut bevel from vertical also creates toe clearance without a bullnose overhang. Pair your finished stair risers with compliant sloped guard spacing from our Stair Baluster 4-3/8" Sphere Guide.

Primary Standards & Building Code Authorities (2024 IRC Sections R311.7.5.1 (Open Risers) & R311.7.5.3 (Nosings))

All dimensions, tolerances, and safety thresholds in this field guide are cross-referenced against current US residential building, electrical, and trade standards:

  • ICC International Residential Code (IRC R311.7) Stairway rise/run geometry, headroom, and handrail code requirements. ICC Digital Codes →
  • NFPA 70 / National Electrical Code (NEC 690) Photovoltaic Voc temperature coefficients, ampacity, and OCPD sizing. NFPA Standards →
  • TCNA Handbook & ANSI A108.02 Ceramic and porcelain tile centering, lippage, and EJ171 expansion joints. TCNA Council →
  • APA Engineered Wood & AWC NDS Structural wood panel sizing, kerf allowances, and framing lumber spans. APA Wood →

Pre-Calculated Blueprints for Stair Stringer Calculator (12 Specs)

Related Calculators & Framing & Stairs Hub

Stair Stringer Calculator
2024 IRC Section R311.7
Roof Rafter Calculator
2024 IRC Section R802
Deck Baluster Calculator
2024 IRC Section R312.1.3
Stud Wall Framing Calculator
2024 IRC Section R602.3
Deck Beam Span Calculator
2024 IRC Section R507
Floor Joist Span Calculator
2024 IRC Section R502.3
Rafter Span Calculator
2024 IRC Section R802.4
Ceiling Joist Span Calculator
2024 IRC Section R802.5
Header Size Calculator
2024 IRC Section R602.7
Roof Pitch Calculator
Trigonometry (rise/run)

Frequently Asked Questions: 2024 IRC Sections R311.7.5.1 (Open Risers) & R311.7.5.3 (Nosings)

How do you measure 10-inch minimum tread depth when stairs have a 1-inch bullnose overhang?

▼

Under 2024 IRC Section R311.7.5.2, tread depth is ALWAYS measured horizontally from vertical plane of the foremost projection of one nosing to the vertical plane of the foremost projection of the adjacent nosing ("nosing-to-nosing" = exact stringer unit run!). A 10-inch stringer run topped with an 11-inch bullnose tread still measures 10.00 inches nosing-to-nosing—not 11 inches!

Why does IRC cap maximum nosing overhang at 1-1/4 inches instead of allowing 2-inch overhangs?

▼

Overhangs exceeding 1-1/4 inches catch the upward-moving toe or boot lip of a person climbing the stairs (causing forward trip falls) and suffer high cantilever splitting shear along the wood grain when adults land heavily on the front edge of an oak tread.

Do exterior deck stairs using two 5/4x6 composite boards need a 3/4-inch overhang beyond a closed PVC riser?

▼

Check your total nosing-to-nosing unit run! Two 5/4×6 deck boards (5.50" + 5.50" + 0.125" gap = 11.125" total width): if mounted flush over an 11-1/8" stringer run with a 3/4" riser board tucked under the back of the upper step, your unit run is already ≥11 inches OR naturally overhangs the lower riser by 3/4" to 1"—passing IRC R311.7.5.3 either way!