Skip to main content
LAYOUTCALCULATOR SCALE 1/16" CAD
NFPA 70 (2023/2026 NEC) Sections 690.8 & 690.9
NFPA 70 (2023/2026 NEC) Sections 690.8 & 690.9 10 min read • Updated

NEC 690.9 Solar String Fuses: 1P & 2P vs 3P+ Combiners (NFPA 70 (2023/2026 NEC) Sections 690.8 & 690.9)

Learn why 1P and 2P solar arrays skip string fuses under NEC 690.9(A) while 3P+ parallel arrays require 1.56x Isc gPV fuses or DC breakers.

Published by LayoutCalculator • Formulas reference published code tables; confirm with your local building official.
Companion 2D SVG CAD Instrument

Need an Instant Scale Blueprint? Launch Solar Wiring & NEC Calculator

Generate real-time 1/16" fractional dimensions, framing square marks, and printable workshop sheets.

Open the Solar Wiring & NEC Calculator →
Direct Code Summary • NFPA 70 (2023/2026 NEC) Sections 690.8 & 690.9 SPEC BULLETIN

What Is the Standard Rule for NEC 690.9 Solar String Fuses?

NFPA 70 (2023/2026 NEC) Sections 690.8 & 690.9: Under NEC 690.9(A)(1), single-string (1P) and two-parallel-string (2P, such as 2S2P or 4S2P) arrays almost NEVER require individual string fuses because backfeed fault current from 1 healthy string cannot exceed the panel’s Max Series Fuse Rating! Connecting 3 or more strings in parallel (3P, 4P, 6P) ALWAYS requires an overcurrent fuse or breaker on EVERY string because (N - 1) healthy strings can dump 2.5×+ Isc backward into one shorted string and ignite its backsheet!

LIVE FIELD SOLVER

Interactive Jobsite Verification Instrument

NFPA 70 (2023/2026 NEC) Sections 690.8 & 690.9
Instant Field Calculation
124.5V STC • 141.9V Cold Voc (-10°C)
Adjust inputs above for live takeoff

Key Engineering & Code Takeaways

  • Under NEC 690.9(A)(1), single-string (1P) and two-parallel-string (2P, such as 2S2P or 4S2P) arrays almost NEVER require individual string fuses because backfeed fault current from 1 healthy string cannot exceed the panel’s Max Series Fuse Rating!
  • Connecting 3 or more strings in parallel (3P, 4P, 6P) ALWAYS requires an overcurrent fuse or breaker on EVERY string because (N - 1) healthy strings can dump 2.5×+ Isc backward into one shorted string and ignite its backsheet!
  • Size PV string fuses per NEC 690.8 & 690.9(B) to at least 1.56 × Module Isc rounded up to the next standard rating, without exceeding the UL 61730 Maximum Series Fuse Rating printed on the module label.
  • Only install UL 248-19 1000V/1500V DC gPV finger-safe fuses (never open fuse holders under load!) or UL 489B non-polarized DC circuit breakers inside a NEMA 3R/4X combiner box.

Part of our Solar & Electrical series; start with NEC 690.7 Cold Weather Solar Voc Formula & MPPT Sizing. Related: NEC 690.12 Solar Rapid Shutdown, Solar Panel Frame Bonding & EGC Wire Sizing (NEC 690.43), EMT & PVC Conduit Fill Chart for 10 AWG PV Wire (NEC 9).

NEC 690.9 Parallel String Backfeed Fault Math & Fuse Requirement Table (400W Panel: Isc = 13.8A, Max Series Fuse = 25A)

← Swipe table horizontally → NFPA 70 (2023/2026 NEC) Sections 690.8 & 690.9
NEC 690.9 Parallel String Backfeed Fault Math & Fuse Requirement Table (400W Panel: Isc = 13.8A, Max Series Fuse = 25A) (NFPA 70 (2023/2026 NEC) Sections 690.8 & 690.9)
Parallel StringsMax Reverse Fault (N-1)×1.25×IscVs 25A Panel LimitString Fuses Required?Min Home-Run Wire (×1.56 Isc)
1P (e.g. 4S1P, 8S1P) 0 × 17.25A = 0.0 A 0.0A ≤ 25A (Safe) NO Fuse Needed (690.9(A)(1)) 21.5A min → 10 AWG Cu (30A)
2P (e.g. 2S2P, 4S2P) 1 × 17.25A = 17.3 A 17.3A ≤ 25A (Safe) NO String Fuse Needed! 43.1A min → 8 AWG Cu (50A)
3P (e.g. 2S3P, 3S3P) 2 × 17.25A = 34.5 A 34.5A exceeds 25A! YES — Three 25A gPV Fuses! 64.6A min → 6 AWG Cu (65A)
4P (e.g. 1S4P, 2S4P) 3 × 17.25A = 51.8 A 51.8A exceeds 25A! YES — Four 25A gPV Fuses! 86.1A min → 3 AWG Cu (100A)
5P (Combiner Array) 4 × 17.25A = 69.0 A 69.0A exceeds 25A! YES — Five 25A gPV Fuses! 107.6A min → 2 AWG Cu (115A)
6P (Combiner Array) 5 × 17.25A = 86.3 A 86.3A exceeds 25A! YES — Six 25A gPV Fuses! 129.2A min → 1 AWG Cu (130A)

1. Why Solar Panels Cannot Trip Their Own Fuse in 1P or 2P—And Why 3P+ Burns Wires

Residential electricians accustomed to 200-Amp AC utility panels (which can deliver 10,000 Amps of instantaneous fault current to snap a 20A breaker in milliseconds) are often baffled by solar PV overcurrent physics. A solar panel is a current-limited semiconductor source: a 400W panel with a nameplate Short-Circuit Current (Isc) of 13.8 Amps produces about 12.9 Amps under normal load and only 13.8A × 1.25 = 17.25 Amps even if you bolt its positive and negative MC4 leads directly together in bright desert sun! Put a 25-Amp fuse inline on a single 1P string, short the cable, and that 25A fuse will sit at 17.25A forever without blowing.

Why then does UL test and stamp a Maximum Series Fuse Rating (typically 20A, 25A, or 30A) on the back of every solar module? To protect against parallel reverse backfeed! Under NEC Section 690.9(A)(1), in a 2P array (two strings joined with MC4 branch Y-connectors), if String 1 suffers a shorted bypass diode or crushed wire, only one healthy string (String 2) pushes fault current backward into String 1 (17.25A ≤ 25A panel fuse limit—100% safe without string fuses, provided the combined home-run wire after the Y-connector is rated for 2 × 13.8A × 1.56 = 43.1A, i.e., 8 AWG!). The instant you connect a third parallel string (3P), two healthy strings dump 2 × 17.25A = 34.5 Amps backward into the single faulted string—exceeding its 25A backsheet and 12 AWG factory lead rating! Verify your exact 1P / 2P / 3P fuse requirement automatically in our Solar Panel Series-Parallel & NEC Calculator.

2. Step-by-Step NEC 690.8 & 690.9(B) String Fuse Sizing Worked Example

Suppose you are combining three parallel strings of 3S3P (nine 410W solar panels total) where each module’s rear UL 61730 datasheet sticker lists Voc = 37.5V, Isc = 13.95A, and Maximum Series Fuse Rating = 25A:

  • Step 1 (Maximum String Circuit Current — NEC 690.8(A)(1)): Multiply single-string Isc by 1.25 for cloud-edge irradiance enhancement above 1,000 W/m²: 13.95A × 1.25 = 17.44 Amps.
  • Step 2 (Continuous-Duty Overcurrent Sizing — NEC 690.8(B)(1)): Multiply Maximum Current by another 1.25 for 3+ hours continuous daylight duty (1.25 × 1.25 = 1.5625 total multiplier): 13.95A × 1.56 = 21.76 Amps.
  • Step 3 (Round Up & Check Panel Ceiling — NEC 690.9(B)): Round 21.76A up to the next standard overcurrent device size in NEC Table 240.6(A): 25 Amps. Check that 25A ≤ 25A Maximum Series Fuse Rating on the panel sticker—PASS! Install one 25A DC gPV fuse (or 25A non-polarized DC breaker) on the positive leg of each of the 3 strings inside a solar combiner box.
  • Step 4 (Size Combiner Output Bus & Home-Run Wire): Total combined array Isc = 3 × 13.95A = 41.85A; multiply by 1.56 = 65.3 Amps → Pull 4 AWG Copper THWN-2 (85A @ 75°C) from the combiner output disconnect down to the MPPT controller!

3. Deadly Hardware Traps: Inline MC4 Fuse Holders, AC Breakers & Polarized DC Breakers

Three cheap online hardware mistakes routinely melt solar combiner enclosures:

1. Never use cheap waterproof inline MC4 fuse holders on high-current roofs: Tiny crimp springs inside bargain inline MC4 fuse barrels develop contact resistance under thermal cycling, charring plastic on 13A+ panels, and unplugging them under sun load draws a blinding plasma arc! Use a proper DIN-rail touch-safe 10×38mm 1000V DC gPV fuse holder paired with a load-break main DC disconnect switch (always turn off the load-break switch before opening any finger-safe fuse drawer, which is labeled "DO NOT OPEN UNDER LOAD"!).

2. Never use AC Square D / HomeLine breakers OR polarized DC breakers on parallel PV strings: AC arcs cross zero Volts 120 times per second; pure 150V–500V DC never crosses zero and sustains a 3,000°C blowtorch arc inside an AC breaker! Worse still, cheap polarized DC breakers (+ and - markings) rely on permanent arc-chute magnets that extinguish current flowing in only one direction—when reverse fault current flows backward into a shorted PV string, a polarized DC breaker catches fire! Specify only UL 489B Listed Non-Polarized PV DC Breakers (such as MidNite Solar MNEPV) or UL 248-19 gPV fuses.

Primary Standards & Building Code Authorities (NFPA 70 (2023/2026 NEC) Sections 690.8 & 690.9)

All dimensions, tolerances, and safety thresholds in this field guide are cross-referenced against current US residential building, electrical, and trade standards:

  • ICC International Residential Code (IRC R311.7) Stairway rise/run geometry, headroom, and handrail code requirements. ICC Digital Codes →
  • NFPA 70 / National Electrical Code (NEC 690) Photovoltaic Voc temperature coefficients, ampacity, and OCPD sizing. NFPA Standards →
  • TCNA Handbook & ANSI A108.02 Ceramic and porcelain tile centering, lippage, and EJ171 expansion joints. TCNA Council →
  • APA Engineered Wood & AWC NDS Structural wood panel sizing, kerf allowances, and framing lumber spans. APA Wood →

Pre-Calculated Blueprints for Solar Wiring & NEC Calculator (12 Specs)

Related Calculators & Solar & Electrical Hub

Solar Wiring & NEC Calculator
NFPA 70 / NEC Article 690 (2023/2026)

Frequently Asked Questions: NFPA 70 (2023/2026 NEC) Sections 690.8 & 690.9

Do I fuse just the Positive (+) string wire, or both Positive (+) and Negative (-) wires?

▼

On modern functionally ungrounded / transformerless PV arrays (which comprise 99% of modern grid-tied string inverters and isolated/floating MPPT charge controllers), NEC 690.9(C) requires a single overcurrent fuse/breaker in only ONE leg of each string—universally placed in the Positive (+) conductor while all Negative (-) string leads land cleanly on an unfused negative combiner busbar.

Why can’t I just put one big 45A inline fuse after a 3-way MC4 branch connector instead of fusing all 3 strings?

▼

Because a single 45A fuse located downstream toward the charge controller never sees reverse fault current circulating right up on the roof between String 1, String 2, and a shorted String 3! Each of the 3 strings MUST have its own individual 25A fuse upstream of the parallel combining point.

What if my MPPT controller has two separate PV1 and PV2 MPPT tracker inputs?

▼

Independent MPPT tracker channels (with truly isolated inputs—check your inverter manual whether MPPT1A and MPPT1B are internally bussed together!) count separately! Putting 2S2P on MPPT Tracker #1 and 2S2P on an independent MPPT Tracker #2 keeps each sub-array at 2P, avoiding string fuses on both trackers.