Skip to main content
LAYOUTCALCULATOR SCALE 1/16" CAD
NFPA 70 (2023/2026 NEC) Table 310.16, 110.14(C) & 250.32
NFPA 70 (2023/2026 NEC) Table 310.16, 110.14(C) & 250.32 12 min read • Updated

50A, 60A & 100A Subpanel Feeder Wire Chart (NEC 310.16)

Size 4-wire 240V garage and inverter subpanel feeders from 50 ft to 200 ft using 75°C copper vs aluminum ampacity, 3% drop, and NEC 250.32.

Published by LayoutCalculator • Formulas reference published code tables; confirm with your local building official.
Companion 2D SVG CAD Instrument

Need an Instant Scale Blueprint? Launch Solar Wiring & NEC Calculator

Generate real-time 1/16" fractional dimensions, framing square marks, and printable workshop sheets.

Open the Solar Wiring & NEC Calculator →
Direct Code Summary • NFPA 70 (2023/2026 NEC) Table 310.16, 110.14(C) & 250.32 SPEC BULLETIN

What Is the Standard Rule for 50A, 60A & 100A Subpanel Feeder Wire Chart (NEC 310.16)?

NFPA 70 (2023/2026 NEC) Table 310.16, 110.14(C) & 250.32: Every post-2008 NEC 120/240V subpanel requires a 4-wire feeder (Hot L1, Hot L2, Insulated Neutral, Equipment Ground) with the green neutral-bonding screw REMOVED so neutral floats isolated from the metal box! Per NEC 110.14(C), subpanel breaker lugs cap THWN-2, XHHW-2, SER, and MHF conductors to the 75°C column of Table 310.16—while indoor NM-B (Romex) is strictly locked to the lower 60°C column (NEC 334.80)!

LIVE FIELD SOLVER

Interactive Jobsite Verification Instrument

NFPA 70 (2023/2026 NEC) Table 310.16, 110.14(C) & 250.32
Instant Field Calculation
8 AWG Copper (1.14V Drop)
Adjust inputs above for live takeoff

Key Engineering & Code Takeaways

  • Every post-2008 NEC 120/240V subpanel requires a 4-wire feeder (Hot L1, Hot L2, Insulated Neutral, Equipment Ground) with the green neutral-bonding screw REMOVED so neutral floats isolated from the metal box!
  • Per NEC 110.14(C), subpanel breaker lugs cap THWN-2, XHHW-2, SER, and MHF conductors to the 75°C column of Table 310.16—while indoor NM-B (Romex) is strictly locked to the lower 60°C column (NEC 334.80)!
  • 2-2-2-4 Aluminum MHF/SER is rated for 90 Amps MAXIMUM on a subpanel feeder (the 100A 83% dwelling rule in 310.12 does NOT apply to garage subpanels!); step up to 1 AWG Aluminum or 3 AWG Copper for a true 100A breaker!
  • For detached garages and solar sheds, NEC 250.32(B)(1) requires BOTH pulling the 4th equipment ground wire in the trench AND driving two local 8-foot ground rods spaced at least 6 feet apart.

Part of our Solar & Electrical series; start with NEC 690.7 Cold Weather Solar Voc Formula & MPPT Sizing. Related: NEC 210.52 Outlet Spacing, Solar Panels in Series vs. Parallel, Solar DC Wire Size Guide.

NEC Table 310.16 (75°C Terminal Rule) 240V 4-Wire Subpanel Feeder Sizing & 3% Voltage Drop Chart

← Swipe table horizontally → NFPA 70 (2023/2026 NEC) Table 310.16, 110.14(C) & 250.32
NEC Table 310.16 (75°C Terminal Rule) 240V 4-Wire Subpanel Feeder Sizing & 3% Voltage Drop Chart (NFPA 70 (2023/2026 NEC) Table 310.16, 110.14(C) & 250.32)
Subpanel BreakerMin Copper (75°C THWN-2)Min Aluminum (75°C SER/MHF)Min EGC (Cu / Al)Upsize @ 150 ft / 200 ft (≤ 3% Drop @ 80% Load)
30A Subpanel (24A Load) 10 AWG Cu (30A; 10/3 NM-B ok) 8 AWG Al (40A) 10 AWG Cu / 8 AWG Al 8 AWG Cu @ 150 ft / 6 AWG Cu @ 200 ft
50A Subpanel (40A Load) 8 AWG THWN-2 (50A; 6/3 NM-B!) 6 AWG Al (50A) 10 AWG Cu / 8 AWG Al 6 AWG Cu (4 Al) @ 150 ft / 4 Cu (2 Al) @ 200 ft
60A Subpanel (48A Load) 6 AWG THWN-2 (65A; Note NM-B!) 4 AWG Al (65A) 10 AWG Cu / 8 AWG Al 4 AWG Cu (2 Al) @ 150 ft / 3 Cu (1 Al) @ 200 ft
90A Budget Sweet Spot! 4 AWG THWN-2 (85A→90A 240.4B) 2-2-2-4 Al MHF/SER (90A!) 8 AWG Cu / 6 AWG Al 3 AWG Cu (1/0 Al) @ 150 ft / 2 Cu (2/0 Al) @ 200 ft
100A Subpanel (80A Load) 3 AWG THWN-2 (100A) 1 AWG Al (100A) 8 AWG Cu / 6 AWG Al 2 AWG Cu (2/0 Al) @ 150 ft / 1 Cu (3/0 Al) @ 200 ft
125A Solar Hybrid Panel 1 AWG THWN-2 (130A) 2/0 AWG Al (135A) 6 AWG Cu / 4 AWG Al 1/0 Cu (3/0 Al) @ 150 ft / 2/0 Cu (4/0 Al) @ 200 ft

1. The Two Classic NEC Subpanel Traps: 6/3 NM-B @ 60°C & 2-2-2-4 Aluminum @ 90A

Two internet forum myths cause thousands of failed garage and hybrid-inverter subpanel inspections every year. Trap #1 (6/3 NM-B Romex on a 60A Subpanel): Under NEC 110.14(C), individual THWN-2 wires in conduit use the 75°C column of NEC Table 310.16 (6 AWG Cu = 65 Amps), easily handling a 60A breaker. However, nonmetallic indoor NM-B (Romex) cable is restricted by NEC 334.80 to the 60°C column, where 6 AWG Cu is rated for only 55 Amps! Under the round-up rule of NEC 240.4(B), you may protect 55A 6/3 NM-B with a 60A breaker ONLY if your calculated continuous + noncontinuous subpanel load is 55 Amps or less (for example, NOT a 48A EV charger 48 × 1.25 = 60A plus shop tools!). For underground trenches, NEVER pull indoor paper-wrapped NM-B inside outdoor PVC conduit (all outdoor/underground conduits are classified as Wet Locations per NEC 300.5(B)—pull individual THWN-2 or direct-burial MHF / UF-B!).

Trap #2 (2-2-2-4 Aluminum MHF on a 100A Breaker): Homeowners see 2 AWG Aluminum used on 100A mobile-home main services and slap a 100A feed breaker on it for a detached garage. Under NEC 310.12, the favorable 83% dwelling rating (100A × 0.83 = 83A) applies ONLY when a feeder carries 100% of the entire dwelling unit’s load! A workshop, barn, or solar critical-loads subpanel does not carry the whole house, so 2 AWG Aluminum is strictly capped at its 75°C Table 310.16 rating of 90 Amps! Simply snap a 90-Amp 2-pole feed breaker into your main panel (even if the garage subpanel itself came from the store with a 100A or 125A local main disconnect switch) and enjoy 2-2-2-4 Aluminum Mobile Home Feeder at roughly one-third the cost of copper! Compare DC and AC wire resistance values anytime in our Solar Panel Series-Parallel & NEC Calculator.

2. Worked 240V Voltage Drop Calculation: 150-Foot Trench to a Detached Solar Workshop

NEC 215.2(A)(1) Informational Note 2 recommends keeping feeder voltage drop under 3% maximum (240V × 0.03 = 7.20 Volts max drop) so table saws, air compressors, and grid-interactive hybrid solar inverters (which trip high-voltage grid faults if narrow feeder resistance pushes inverter voltage past 264V while exporting!) run reliably. Let us check 2-2-2-4 Aluminum (66,360 circular mils, K_Al = 21.2) carrying 72 Amps (80% of a 90A feeder) across a 150-foot one-way trench:

  • Step 1 (Apply Single-Phase 2-Way Voltage Drop Formula): Compute VD = (2 × K × I × L) ÷ CM = (2 × 21.2 × 72A × 150 ft) ÷ 66,360 CM = 457,920 ÷ 66,360 = 6.90 Volts.
  • Step 2 (Convert to Percentage of 240V): Divide by system voltage: 6.90V ÷ 240V = 2.88% voltage drop—passing right beneath the 3.0% ceiling at 150 feet!
  • Step 3 (At 200 Feet): Extending that exact 72A load to 200 feet pushes drop to 9.20V (3.83%)—so at 200 feet you upsize one step to 1/0 AWG Aluminum (105,600 CM, yielding 5.78V = 2.41% drop) AND remember NEC 250.122(B): whenever you upsize phase conductors for voltage drop, upsize the Equipment Grounding Conductor by the exact same circular-mil ratio!

3. Detached Building Rules: Floating Neutral Bar + Main Disconnect + Dual Ground Rods (NEC 250.32)

Inside the main utility service disconnect panel of your house, Neutral (white) and Ground (green/bare) are bonded together at one single point (NEC 250.24). Inside every downstream subpanel—whether attached in the basement or 150 feet away in a detached pole barn—you MUST keep Neutral and Equipment Ground 100% isolated! Unscrew and discard the green neutral-bonding screw (or snap out the bonding strap), purchase an accessory metal ground bar kit bolted directly to the steel subpanel tub for all green/bare wires, and land white neutral wires exclusively on the insulated plastic-standoff neutral bar so neutral return current never electrifies metal conduit or chassis frames.

Whenever a feeder supplies a separate detached building (detached garage, workshop, solar shed), three additional NEC mandates trigger: (1) Trench Burial Depth (NEC Table 300.5): 24 inches cover for direct-buried MHF cable (RHW-2/USE-2), 18 inches inside Schedule 40/80 PVC conduit, or 6 inches inside Rigid Metal Conduit (RMC); (2) Building Disconnecting Means (NEC 225.31): if supplying more than a single branch circuit, the subpanel at the detached building needs a local main breaker (which acts simply as a shutoff switch—a 100A/125A main-breaker subpanel fed by a 60A or 90A house breaker is 100% legal!); and (3) Grounding Electrode System (NEC 250.32(B)(1) & 250.53(A)(3)): drive two 8-foot copper-clad ground rods spaced at least 6 feet apart outside the garage and connect them with 6 AWG bare copper solely to the subpanel’s isolated Ground Bar (never the neutral bar!).

Primary Standards & Building Code Authorities (NFPA 70 (2023/2026 NEC) Table 310.16, 110.14(C) & 250.32)

All dimensions, tolerances, and safety thresholds in this field guide are cross-referenced against current US residential building, electrical, and trade standards:

  • ICC International Residential Code (IRC R311.7) Stairway rise/run geometry, headroom, and handrail code requirements. ICC Digital Codes →
  • NFPA 70 / National Electrical Code (NEC 690) Photovoltaic Voc temperature coefficients, ampacity, and OCPD sizing. NFPA Standards →
  • TCNA Handbook & ANSI A108.02 Ceramic and porcelain tile centering, lippage, and EJ171 expansion joints. TCNA Council →
  • APA Engineered Wood & AWC NDS Structural wood panel sizing, kerf allowances, and framing lumber spans. APA Wood →

Pre-Calculated Blueprints for Solar Wiring & NEC Calculator (12 Specs)

Related Calculators & Solar & Electrical Hub

Solar Wiring & NEC Calculator
NFPA 70 / NEC Article 690 (2023/2026)

Frequently Asked Questions: NFPA 70 (2023/2026 NEC) Table 310.16, 110.14(C) & 250.32

Can I pull 2-2-2-4 Aluminum MHF indoors through house floor joists all the way to my main panel?

▼

Watch out! Standard individual-conductor 2-2-2-4 MHF (Mobile Home Feeder, dual-rated RHW-2/USE-2) lacks a flame-retardant outer sheath, so NEC 338.12(B) prohibits running bare USE-2 conductors exposed indoors outside of conduit! Either run continuous Schedule 40/80 PVC or EMT conduit all the way from panel to panel, OR transition inside a junction box where the trench enters the house to jacketed 2-2-2-4 Aluminum SER cable (Service Entrance Round, which has a fire-rated gray PVC jacket legal to staple through indoor joists just like Romex!).

Do I need anti-oxidant paste (Noalox) and a torque screwdriver on modern AA-8000 Aluminum feeder lugs?

▼

Modern AA-8000 series aluminum building wire (mandatory since the 1980s) eliminates the thermal creep of 1970s AA-1350 branch wire, and NEC 110.14 only mandates anti-oxidant compound if required by the lug/breaker manufacturer instructions (though brushing a thin dab of Noalox on stripped strands remains smart corrosion insurance). What IS strictly mandatory under NEC 110.14(D) is tightening every feeder lug with a calibrated inch-pound / foot-pound torque wrench to the exact value stamped inside the panel door!

What is the 120% Solar Backfeed Rule (NEC 705.12(B)(3)(2)) when feeding a solar inverter into a 200A panel?

▼

On a 200A main panel with a 200A main utility breaker, total breaker ratings feeding the busbar (Utility Main + Solar Backfeed Breaker) cannot exceed 120% of the busbar rating when the solar breaker is placed at the opposite end of the busbar from the main breaker: (200A × 1.20) - 200A = 40 Amps max solar breaker (7.6 kW inverter)! Upgrading to a 225A-busbar / 200A-main-breaker "Solar Ready" panel jumps that allowance straight to (225A × 1.20) - 200A = 70 Amps!