Skip to main content
LAYOUTCALCULATOR SCALE 1/16" CAD
AWI Section 6 Finish Trim • SCALE: 1/16" FRACTIONAL
38°/45° Compound Saw Trig Finish Carpentry & Trim

120° Tray Ceiling (38°) — 120° Hexagonal & Coffered Tray Ceiling Crown Angles

Pre-solved compound miter (19.6°) and bevel (23.2°) angles for 38-degree crown molding inside 120-degree hexagonal turrets and angled tray ceilings.

Calculation notes
Checked against: AWI Section 6 Finish Trim
Published by LayoutCalculator. Confirm with your local building official.
REV DATE:
Result summary

Six-sided hexagonal rooms and 120° tray soffits deflect 30.0° per joint. Laying 38° spring crown flat requires a 19.6° miter swing and 23.2° left bevel tilt (or 30.0° miter nested).

Typical Field Application

Victorian turret bedrooms, hexagonal gazebos, and recessed polygonal dining room tray ceilings.

Field note

In recessed tray ceilings with indirect LED rope lighting behind the crown, install a continuous level 1x3 wood cleat so every mitered stick sits dead straight.

AWI SECTION 6 2D SVG Crown Molding Compound Miter & Bevel Console
Miter 19.6°
Bevel 23.2° L
Fence Check PASS (38°)
120.0° (Inside)
60° (Acute) 88° (Tight) 90° (Square) 135° (Bay)
44 LF (51 LF w/ 15%)
24' (Cabinet) 48' (12x12) 64' (14x18) 200' (Whole Flr)
✓ AWI SECTION 6 COMPOUND SPEC 38°/52° Spring

For a 120.0° inside corner (30.00° half-turn), set miter to 19.6° and bevel to 23.2°. Dry-fit scrap blocks to verify tight face closure.

2D Crown Molding Compound Miter Saw Turntable & Bevel Protractor Blueprint Interactive CAD dial diagram showing exact miter saw turntable swing angle, rear bevel tilt protractor, molding fence orientation, wall drop, and ceiling projection. MITER SWING: 19.6° | BEVEL TILT: 23.2° LEFT | CORNER: 120.0° (INSIDE) FLAT ON SAW TABLE • CEILING/WALL EDGE AT FENCE • SPRING: 38°/52° TOP-DOWN MITER TURNTABLE (19.6°) SAW FENCE (TOP CEILING EDGE FOR INSIDE-L / OUTSIDE-R) CROWN FACE UP (4-1/2") 0° 45° L 45° R Set Miter: 19.6° L / R REAR BEVEL TILT (23.2° LEFT) 0° Tilt Blade 23.2° Left SPRING TRIANGLE (38° WALL / 52° CEILING) Ceil Proj: 2-3/4" Wall Drop: 3-9/16" Face: 4-1/2"
Saw Miter Angle
19.6°
30.0° Half-Turn
Saw Bevel Tilt
23.2°
Left Bevel Tilt
Wall Drop Height
3-9/16"
3.55" Down Wall
Ceil. Projection
2-3/4"
2.77" Across Ceil
16-Ft Trim Sticks
4 Sticks
51 LF (Incl. 15% Waste)

Left vs. Right Piece Saw Fence & Swing Schedule Single-Bevel Left

Follow exact edge-against-fence orientation below so compound miters close tightly at 120.0° corners without reverse-cut scrap:

Crown Molding Left and Right Piece Miter Saw Fence Orientation and Swing Schedule
Corner Piece Edge Against Fence Miter Swing Bevel & Save
Inside Corner — Left Piece Top (Ceiling) Edge at Fence 19.6° RIGHT 23.2° LEFT • Save Left
Inside Corner — Right Piece Bottom (Wall) Edge at Fence 19.6° LEFT 23.2° LEFT • Save Left
Outside Corner — Left Piece Bottom (Wall) Edge at Fence 19.6° LEFT 23.2° LEFT • Save Right
Outside Corner — Right Piece Top (Ceiling) Edge at Fence 19.6° RIGHT 23.2° LEFT • Save Right

Required Bill of Materials (BOM) & Trim Hardware

+15% Miter Waste Included
  • 4 × 16-ft Crown Molding Sticks (4-1/2" Face • 38° Spring) 51 gross LF for 44 LF perimeter (or 5 × 12-ft sticks)
  • 1 × Digital Angle Finder Protractor (±0.1° Stainless Arm) Reads exact 120.0° drywall corner (30.00° half-turn deflection)
  • 15-Gauge 2-1/2" Finish Nails + 2P-10 CA Miter Adhesive Kit AWI Section 6 best practice: pre-glue outside miters on bench and cope inside MDF/pine joints

Independent Field Spec Notice: Compound trigonometric angles and trim waste factors follow AWI Architectural Woodwork Standards Section 6 with zero manufacturer sponsorship.

Need an ad-free Saw Bench Cut Sheet + Vector .SVG protractor?

Pre-Calculated Crown Molding Calculator Blueprints (12 Field Specs)

Select any standard jobsite specification below to load its exact 2D SVG diagram and engineering tables:

Open Base Crown Molding Calculator →
Contractor & Instructor Widget

Embed This 2D SVG Instrument on Your Website (Ad-Free)

Carpentry instructors, trade schools, and builders can embed the standalone ad-free version of this 2D CAD calculator with one HTML snippet.

SPECIFICATION WALKTHROUGH // 120° Tray Ceiling (38°)

Mathematical Derivation & Field Specifications: 120° Tray Ceiling (38°)

Updated • Published by LayoutCalculator

Cutting 38° spring-angle crown molding (4-1/2" face width) flat on the compound miter saw table for a 120° inside corner converts the 30.0° wall half-turn into an exact turntable miter of 19.6° and a saw blade bevel tilt of 23.2° (or 30.0° miter at 0.0° bevel if nested upside-down against the saw fence).

Once sprung against the wall at 38°, this 4-1/2" profile drops 3-9/16" (3.55") vertically down the drywall and projects 2-3/4" (2.77") across the ceiling. Trimming a 44-foot room perimeter with a 15% miter/scarf waste buffer requires 51 linear feet (4 × 16-ft sticks or 5 × 12-ft sticks).

Corner Angle Sensitivity Matrix for 38° Spring Crown Molding

Measured Wall Angle Flat Compound Miter Flat Compound Bevel Nested Upside-Down (0° Bevel)
88° 32.5° 34.5° 46.0° Miter / 0.0° Bevel
90° 31.6° 33.9° 45.0° Miter / 0.0° Bevel
92° 30.7° 33.2° 44.0° Miter / 0.0° Bevel
120° (Selected) 19.6° 23.2° 30.0° Miter / 0.0° Bevel
135° 14.3° 17.6° 22.5° Miter / 0.0° Bevel

4-Piece Inside & Outside Corner Saw Fence Orientation Schedule (120° Corner)

Corner Piece Edge Against Fence Turntable Miter Left Bevel Tilt Keep Side
Inside Left Top (Ceiling) Edge 19.6° Right 23.2° Left Left of Blade
Inside Right Bottom (Wall) Edge 19.6° Left 23.2° Left Right of Blade
Outside Left Bottom (Wall) Edge 19.6° Left 23.2° Left Left of Blade
Outside Right Top (Ceiling) Edge 19.6° Right 23.2° Left Right of Blade

Field Manuals & Code Tables for Crown Molding Calculator

Index of All 107 Manuals →

Frequently Asked Questions (120° Tray Ceiling (38°))

What are the exact flat compound miter and bevel angles for 38° crown molding on a 120° corner?

▼

Laying 38° spring-angle crown flat on your compound miter saw for a 120° inside corner requires setting the turntable miter to 19.6° and tilting the blade bevel to 23.2° (or 30.0° miter at 0.0° bevel if nested upside-down against the fence).

What is the ceiling projection and wall drop witness line for 4-1/2" crown at a 38° spring angle?

▼

A 4-1/2" face-width profile installed at a 38° wall spring angle drops 3-9/16" (3.55") vertically down the wall and projects 2-3/4" (2.77") across the ceiling.

How many 16-ft or 12-ft sticks of crown molding do I need for a 44-ft room perimeter?

▼

Including a 15% compound-miter and corner-scarf waste buffer (51 gross linear feet), order 4 sticks of 16-ft molding (recommended to minimize mid-wall scarf joints) or 5 sticks of 12-ft molding.