Skip to main content
LAYOUTCALCULATOR SCALE 1/16" CAD
AWI Section 6 Finish Trim • SCALE: 1/16" FRACTIONAL
38°/45° Compound Saw Trig Finish Carpentry & Trim

Nested (Upside-Down) @ 90° — Nested Crown Molding Cuts: 38° Spring @ 90° Corner

Cut 5-1/4" 38-degree crown molding nested upside-down and backward against your miter saw fence at a simple 45.0° miter and 0.0° bevel (zero tilt).

Calculation notes
Checked against: AWI Section 6 Finish Trim
Published by LayoutCalculator. Confirm with your local building official.
REV DATE:
Result summary

Nesting 5-1/4" crown upside-down on the saw fence replicates its installed 4-1/8" wall drop and 3-1/4" ceiling projection, letting you cut square 90° corners at 45.0° miter with 0.0° blade bevel.

Typical Field Application

Fast single-bevel miter saws, coping inside joints by hand, and trim carpenters using clamping crown stops.

Field note

Bolt sacrificial auxiliary MDF crown stops to your miter saw base set exactly 3-1/4" out from the fence so the molding cannot slip out of its 38° nested angle mid-cut.

AWI SECTION 6 2D SVG Crown Molding Compound Miter & Bevel Console
Miter 45.0°
Bevel 0.0° L
Fence Check PASS (38°)
90.0° (Inside)
60° (Acute) 88° (Tight) 90° (Square) 135° (Bay)
60 LF (69 LF w/ 15%)
24' (Cabinet) 48' (12x12) 64' (14x18) 200' (Whole Flr)
✓ AWI SECTION 6 COMPOUND SPEC 38°/52° Spring

For a 90.0° inside corner (45.00° half-turn), set miter to 45.0° and bevel to 0.0°. Dry-fit scrap blocks to verify tight face closure.

2D Crown Molding Compound Miter Saw Turntable & Bevel Protractor Blueprint Interactive CAD dial diagram showing exact miter saw turntable swing angle, rear bevel tilt protractor, molding fence orientation, wall drop, and ceiling projection. MITER SWING: 45.0° | BEVEL TILT: 0.0° LEFT | CORNER: 90.0° (INSIDE) NESTED UPSIDE-DOWN • WALL EDGE VERTICAL AT FENCE • SPRING: 38°/52° TOP-DOWN MITER TURNTABLE (45.0°) SAW FENCE (WALL EDGE AGAINST FENCE) CROWN FACE UP (5-1/4") 0° 45° L 45° R Set Miter: 45.0° L / R REAR BEVEL TILT (0.0° LEFT) 0° 0.0° Vertical Blade (Nested) SPRING TRIANGLE (38° WALL / 52° CEILING) Ceil Proj: 3-1/4" Wall Drop: 4-1/8" Face: 5-1/4"
Saw Miter Angle
45.0°
45.0° Half-Turn
Saw Bevel Tilt
0.0°
0° Vertical Blade
Wall Drop Height
4-1/8"
4.14" Down Wall
Ceil. Projection
3-1/4"
3.23" Across Ceil
16-Ft Trim Sticks
5 Sticks
69 LF (Incl. 15% Waste)

Left vs. Right Piece Saw Fence & Swing Schedule Nested 0° Bevel

Follow exact edge-against-fence orientation below so compound miters close tightly at 90.0° corners without reverse-cut scrap:

Crown Molding Left and Right Piece Miter Saw Fence Orientation and Swing Schedule
Corner Piece Edge Against Fence Miter Swing Bevel & Save
Inside Corner — Left Piece Upside-Down (Wall Edge at Fence) 45.0° RIGHT 0.0° Vertical • Save Right
Inside Corner — Right Piece Upside-Down (Wall Edge at Fence) 45.0° LEFT 0.0° Vertical • Save Left
Outside Corner — Left Piece Upside-Down (Wall Edge at Fence) 45.0° LEFT 0.0° Vertical • Save Right
Outside Corner — Right Piece Upside-Down (Wall Edge at Fence) 45.0° RIGHT 0.0° Vertical • Save Left

Required Bill of Materials (BOM) & Trim Hardware

+15% Miter Waste Included
  • 5 × 16-ft Crown Molding Sticks (5-1/4" Face • 38° Spring) 69 gross LF for 60 LF perimeter (or 6 × 12-ft sticks)
  • 1 × Digital Angle Finder Protractor (±0.1° Stainless Arm) Reads exact 90.0° drywall corner (45.00° half-turn deflection)
  • 15-Gauge 2-1/2" Finish Nails + 2P-10 CA Miter Adhesive Kit AWI Section 6 best practice: pre-glue outside miters on bench and cope inside MDF/pine joints

Independent Field Spec Notice: Compound trigonometric angles and trim waste factors follow AWI Architectural Woodwork Standards Section 6 with zero manufacturer sponsorship.

Need an ad-free Saw Bench Cut Sheet + Vector .SVG protractor?

Pre-Calculated Crown Molding Calculator Blueprints (12 Field Specs)

Select any standard jobsite specification below to load its exact 2D SVG diagram and engineering tables:

Open Base Crown Molding Calculator →
Contractor & Instructor Widget

Embed This 2D SVG Instrument on Your Website (Ad-Free)

Carpentry instructors, trade schools, and builders can embed the standalone ad-free version of this 2D CAD calculator with one HTML snippet.

SPECIFICATION WALKTHROUGH // Nested (Upside-Down) @ 90°

Mathematical Derivation & Field Specifications: Nested (Upside-Down) @ 90°

Updated • Published by LayoutCalculator

Cutting 38° spring-angle crown molding (5-1/4" face width) flat on the compound miter saw table for a 90° inside corner converts the 45.0° wall half-turn into an exact turntable miter of 31.6° and a saw blade bevel tilt of 33.9° (or 45.0° miter at 0.0° bevel if nested upside-down against the saw fence).

Once sprung against the wall at 38°, this 5-1/4" profile drops 4-1/8" (4.14") vertically down the drywall and projects 3-1/4" (3.23") across the ceiling. Trimming a 60-foot room perimeter with a 15% miter/scarf waste buffer requires 69 linear feet (5 × 16-ft sticks or 6 × 12-ft sticks).

Corner Angle Sensitivity Matrix for 38° Spring Crown Molding

Measured Wall Angle Flat Compound Miter Flat Compound Bevel Nested Upside-Down (0° Bevel)
88° 32.5° 34.5° 46.0° Miter / 0.0° Bevel
90° (Selected) 31.6° 33.9° 45.0° Miter / 0.0° Bevel
92° 30.7° 33.2° 44.0° Miter / 0.0° Bevel
120° 19.6° 23.2° 30.0° Miter / 0.0° Bevel
135° 14.3° 17.6° 22.5° Miter / 0.0° Bevel

4-Piece Inside & Outside Corner Saw Fence Orientation Schedule (90° Corner)

Corner Piece Edge Against Fence Turntable Miter Left Bevel Tilt Keep Side
Inside Left Top (Ceiling) Edge 31.6° Right 33.9° Left Left of Blade
Inside Right Bottom (Wall) Edge 31.6° Left 33.9° Left Right of Blade
Outside Left Bottom (Wall) Edge 31.6° Left 33.9° Left Left of Blade
Outside Right Top (Ceiling) Edge 31.6° Right 33.9° Left Right of Blade

Field Manuals & Code Tables for Crown Molding Calculator

Index of All 107 Manuals →

Frequently Asked Questions (Nested (Upside-Down) @ 90°)

What are the exact flat compound miter and bevel angles for 38° crown molding on a 90° corner?

▼

Laying 38° spring-angle crown flat on your compound miter saw for a 90° inside corner requires setting the turntable miter to 31.6° and tilting the blade bevel to 33.9° (or 45.0° miter at 0.0° bevel if nested upside-down against the fence).

What is the ceiling projection and wall drop witness line for 5-1/4" crown at a 38° spring angle?

▼

A 5-1/4" face-width profile installed at a 38° wall spring angle drops 4-1/8" (4.14") vertically down the wall and projects 3-1/4" (3.23") across the ceiling.

How many 16-ft or 12-ft sticks of crown molding do I need for a 60-ft room perimeter?

▼

Including a 15% compound-miter and corner-scarf waste buffer (69 gross linear feet), order 5 sticks of 16-ft molding (recommended to minimize mid-wall scarf joints) or 6 sticks of 12-ft molding.