Skip to main content
LAYOUTCALCULATOR SCALE 1/16" CAD
AWI Section 6 Finish Trim • SCALE: 1/16" FRACTIONAL
38°/45° Compound Saw Trig Finish Carpentry & Trim

7-1/4" Grand Crown @ 90° — 7-1/4" Oversized Crown Molding: Flat Compound Cuts

Cut wide 7-1/4" 38-degree architectural crown molding flat on a sliding miter saw (31.6° miter, 33.9° bevel) when tall profiles exceed saw fence height.

Calculation notes
Checked against: AWI Section 6 Finish Trim
Published by LayoutCalculator. Confirm with your local building official.
REV DATE:
Result summary

Oversized 7-1/4" crown cannot stand nested against standard 4-1/2" miter fences—cutting flat on a 10" or 12" slider at 31.6° miter / 33.9° bevel solves capacity with 5-11/16" wall drop.

Typical Field Application

10-foot and 12-foot foyers, formal dining rooms, and two-piece built-up cornice assemblies.

Field note

Because 7-1/4" crown spans 4-7/16" across the ceiling, install triangular 2x4 blocking backing blocks nailed at 16" OC along the wall-ceiling corner before hanging the molding.

AWI SECTION 6 2D SVG Crown Molding Compound Miter & Bevel Console
Miter 31.6°
Bevel 33.9° L
Fence Check PASS (38°)
90.0° (Inside)
60° (Acute) 88° (Tight) 90° (Square) 135° (Bay)
72 LF (83 LF w/ 15%)
24' (Cabinet) 48' (12x12) 64' (14x18) 200' (Whole Flr)
✓ MATCHES SAW CROWN DETENT STOP 38°/52° Spring

Exact 31.6° miter and 33.9° left bevel lock directly into factory crown detents on DeWalt, Makita, Bosch, and Milwaukee saws.

2D Crown Molding Compound Miter Saw Turntable & Bevel Protractor Blueprint Interactive CAD dial diagram showing exact miter saw turntable swing angle, rear bevel tilt protractor, molding fence orientation, wall drop, and ceiling projection. MITER SWING: 31.6° | BEVEL TILT: 33.9° LEFT | CORNER: 90.0° (INSIDE) FLAT ON SAW TABLE • CEILING/WALL EDGE AT FENCE • SPRING: 38°/52° TOP-DOWN MITER TURNTABLE (31.6°) SAW FENCE (TOP CEILING EDGE FOR INSIDE-L / OUTSIDE-R) CROWN FACE UP (7-1/4") 0° 45° L 45° R Set Miter: 31.6° L / R (Crown Detent) REAR BEVEL TILT (33.9° LEFT) 0° Tilt Blade 33.9° Left SPRING TRIANGLE (38° WALL / 52° CEILING) Ceil Proj: 4-7/16" Wall Drop: 5-11/16" Face: 7-1/4"
Saw Miter Angle
31.6°
Crown Detent Stop
Saw Bevel Tilt
33.9°
Left Bevel Tilt
Wall Drop Height
5-11/16"
5.71" Down Wall
Ceil. Projection
4-7/16"
4.46" Across Ceil
16-Ft Trim Sticks
6 Sticks
83 LF (Incl. 15% Waste)

Left vs. Right Piece Saw Fence & Swing Schedule Single-Bevel Left

Follow exact edge-against-fence orientation below so compound miters close tightly at 90.0° corners without reverse-cut scrap:

Crown Molding Left and Right Piece Miter Saw Fence Orientation and Swing Schedule
Corner Piece Edge Against Fence Miter Swing Bevel & Save
Inside Corner — Left Piece Top (Ceiling) Edge at Fence 31.6° RIGHT 33.9° LEFT • Save Left
Inside Corner — Right Piece Bottom (Wall) Edge at Fence 31.6° LEFT 33.9° LEFT • Save Left
Outside Corner — Left Piece Bottom (Wall) Edge at Fence 31.6° LEFT 33.9° LEFT • Save Right
Outside Corner — Right Piece Top (Ceiling) Edge at Fence 31.6° RIGHT 33.9° LEFT • Save Right

Required Bill of Materials (BOM) & Trim Hardware

+15% Miter Waste Included
  • 6 × 16-ft Crown Molding Sticks (7-1/4" Face • 38° Spring) 83 gross LF for 72 LF perimeter (or 7 × 12-ft sticks)
  • 1 × Digital Angle Finder Protractor (±0.1° Stainless Arm) Reads exact 90.0° drywall corner (45.00° half-turn deflection)
  • 15-Gauge 2-1/2" Finish Nails + 2P-10 CA Miter Adhesive Kit AWI Section 6 best practice: pre-glue outside miters on bench and cope inside MDF/pine joints

Independent Field Spec Notice: Compound trigonometric angles and trim waste factors follow AWI Architectural Woodwork Standards Section 6 with zero manufacturer sponsorship.

Need an ad-free Saw Bench Cut Sheet + Vector .SVG protractor?

Pre-Calculated Crown Molding Calculator Blueprints (12 Field Specs)

Select any standard jobsite specification below to load its exact 2D SVG diagram and engineering tables:

Open Base Crown Molding Calculator →
Contractor & Instructor Widget

Embed This 2D SVG Instrument on Your Website (Ad-Free)

Carpentry instructors, trade schools, and builders can embed the standalone ad-free version of this 2D CAD calculator with one HTML snippet.

SPECIFICATION WALKTHROUGH // 7-1/4" Grand Crown @ 90°

Mathematical Derivation & Field Specifications: 7-1/4" Grand Crown @ 90°

Updated • Published by LayoutCalculator

Cutting 38° spring-angle crown molding (7-1/4" face width) flat on the compound miter saw table for a 90° inside corner converts the 45.0° wall half-turn into an exact turntable miter of 31.6° and a saw blade bevel tilt of 33.9° (or 45.0° miter at 0.0° bevel if nested upside-down against the saw fence).

Once sprung against the wall at 38°, this 7-1/4" profile drops 5-11/16" (5.71") vertically down the drywall and projects 4-7/16" (4.46") across the ceiling. Trimming a 72-foot room perimeter with a 15% miter/scarf waste buffer requires 83 linear feet (6 × 16-ft sticks or 7 × 12-ft sticks).

Corner Angle Sensitivity Matrix for 38° Spring Crown Molding

Measured Wall Angle Flat Compound Miter Flat Compound Bevel Nested Upside-Down (0° Bevel)
88° 32.5° 34.5° 46.0° Miter / 0.0° Bevel
90° (Selected) 31.6° 33.9° 45.0° Miter / 0.0° Bevel
92° 30.7° 33.2° 44.0° Miter / 0.0° Bevel
120° 19.6° 23.2° 30.0° Miter / 0.0° Bevel
135° 14.3° 17.6° 22.5° Miter / 0.0° Bevel

4-Piece Inside & Outside Corner Saw Fence Orientation Schedule (90° Corner)

Corner Piece Edge Against Fence Turntable Miter Left Bevel Tilt Keep Side
Inside Left Top (Ceiling) Edge 31.6° Right 33.9° Left Left of Blade
Inside Right Bottom (Wall) Edge 31.6° Left 33.9° Left Right of Blade
Outside Left Bottom (Wall) Edge 31.6° Left 33.9° Left Left of Blade
Outside Right Top (Ceiling) Edge 31.6° Right 33.9° Left Right of Blade

Field Manuals & Code Tables for Crown Molding Calculator

Index of All 107 Manuals →

Frequently Asked Questions (7-1/4" Grand Crown @ 90°)

What are the exact flat compound miter and bevel angles for 38° crown molding on a 90° corner?

▼

Laying 38° spring-angle crown flat on your compound miter saw for a 90° inside corner requires setting the turntable miter to 31.6° and tilting the blade bevel to 33.9° (or 45.0° miter at 0.0° bevel if nested upside-down against the fence).

What is the ceiling projection and wall drop witness line for 7-1/4" crown at a 38° spring angle?

▼

A 7-1/4" face-width profile installed at a 38° wall spring angle drops 5-11/16" (5.71") vertically down the wall and projects 4-7/16" (4.46") across the ceiling.

How many 16-ft or 12-ft sticks of crown molding do I need for a 72-ft room perimeter?

▼

Including a 15% compound-miter and corner-scarf waste buffer (83 gross linear feet), order 6 sticks of 16-ft molding (recommended to minimize mid-wall scarf joints) or 7 sticks of 12-ft molding.