Skip to main content
LAYOUTCALCULATOR SCALE 1/16" CAD
AWI Section 6 Finish Trim • SCALE: 1/16" FRACTIONAL
38°/45° Compound Saw Trig Finish Carpentry & Trim

45° Crown @ 90° Inside — 45° Crown Molding: 90° Inside Cabinet Soffit Cuts

Exact flat compound miter (35.3°) and bevel (30.0°) settings for 3-1/4" 45-degree crown molding in L-shaped 90-degree inside kitchen cabinet corners.

Calculation notes
Checked against: AWI Section 6 Finish Trim
Published by LayoutCalculator. Confirm with your local building official.
REV DATE:
Result summary

For L-shaped upper kitchen cabinets using 3-1/4" 45° crown, set your sliding miter saw to 35.3° (detent) miter and 30.0° (detent) bevel, dropping 2-5/16" onto the cabinet top rail.

Typical Field Application

L-shaped and U-shaped face-frame or frameless Euro kitchen cabinets with top riser nailer strips.

Field note

Cope inside corners on pre-finished stained maple or oak cabinet crown by cutting a 45° nested bevel first and back-cutting along the lacquer profile line with a fine 16-TPI coping blade.

AWI SECTION 6 2D SVG Crown Molding Compound Miter & Bevel Console
Miter 35.3°
Bevel 30.0° L
Fence Check PASS (45°)
90.0° (Inside)
60° (Acute) 88° (Tight) 90° (Square) 135° (Bay)
32 LF (37 LF w/ 15%)
24' (Cabinet) 48' (12x12) 64' (14x18) 200' (Whole Flr)
✓ MATCHES SAW CROWN DETENT STOP 45°/45° Spring

Exact 35.3° miter and 30.0° left bevel lock directly into factory crown detents on DeWalt, Makita, Bosch, and Milwaukee saws.

2D Crown Molding Compound Miter Saw Turntable & Bevel Protractor Blueprint Interactive CAD dial diagram showing exact miter saw turntable swing angle, rear bevel tilt protractor, molding fence orientation, wall drop, and ceiling projection. MITER SWING: 35.3° | BEVEL TILT: 30.0° LEFT | CORNER: 90.0° (INSIDE) FLAT ON SAW TABLE • CEILING/WALL EDGE AT FENCE • SPRING: 45°/45° TOP-DOWN MITER TURNTABLE (35.3°) SAW FENCE (TOP CEILING EDGE FOR INSIDE-L / OUTSIDE-R) CROWN FACE UP (3-1/4") 0° 45° L 45° R Set Miter: 35.3° L / R (Crown Detent) REAR BEVEL TILT (30.0° LEFT) 0° Tilt Blade 30.0° Left SPRING TRIANGLE (45° WALL / 45° CEILING) Ceil Proj: 2-5/16" Wall Drop: 2-5/16" Face: 3-1/4"
Saw Miter Angle
35.3°
Crown Detent Stop
Saw Bevel Tilt
30.0°
Left Bevel Tilt
Wall Drop Height
2-5/16"
2.30" Down Wall
Ceil. Projection
2-5/16"
2.30" Across Ceil
16-Ft Trim Sticks
3 Sticks
37 LF (Incl. 15% Waste)

Left vs. Right Piece Saw Fence & Swing Schedule Single-Bevel Left

Follow exact edge-against-fence orientation below so compound miters close tightly at 90.0° corners without reverse-cut scrap:

Crown Molding Left and Right Piece Miter Saw Fence Orientation and Swing Schedule
Corner Piece Edge Against Fence Miter Swing Bevel & Save
Inside Corner — Left Piece Top (Ceiling) Edge at Fence 35.3° RIGHT 30.0° LEFT • Save Left
Inside Corner — Right Piece Bottom (Wall) Edge at Fence 35.3° LEFT 30.0° LEFT • Save Left
Outside Corner — Left Piece Bottom (Wall) Edge at Fence 35.3° LEFT 30.0° LEFT • Save Right
Outside Corner — Right Piece Top (Ceiling) Edge at Fence 35.3° RIGHT 30.0° LEFT • Save Right

Required Bill of Materials (BOM) & Trim Hardware

+15% Miter Waste Included
  • 3 × 16-ft Crown Molding Sticks (3-1/4" Face • 45° Spring) 37 gross LF for 32 LF perimeter (or 4 × 12-ft sticks)
  • 1 × Digital Angle Finder Protractor (±0.1° Stainless Arm) Reads exact 90.0° drywall corner (45.00° half-turn deflection)
  • 15-Gauge 2-1/2" Finish Nails + 2P-10 CA Miter Adhesive Kit AWI Section 6 best practice: pre-glue outside miters on bench and cope inside MDF/pine joints

Independent Field Spec Notice: Compound trigonometric angles and trim waste factors follow AWI Architectural Woodwork Standards Section 6 with zero manufacturer sponsorship.

Need an ad-free Saw Bench Cut Sheet + Vector .SVG protractor?

Pre-Calculated Crown Molding Calculator Blueprints (12 Field Specs)

Select any standard jobsite specification below to load its exact 2D SVG diagram and engineering tables:

Open Base Crown Molding Calculator →
Contractor & Instructor Widget

Embed This 2D SVG Instrument on Your Website (Ad-Free)

Carpentry instructors, trade schools, and builders can embed the standalone ad-free version of this 2D CAD calculator with one HTML snippet.

SPECIFICATION WALKTHROUGH // 45° Crown @ 90° Inside

Mathematical Derivation & Field Specifications: 45° Crown @ 90° Inside

Updated • Published by LayoutCalculator

Cutting 45° spring-angle crown molding (3-1/4" face width) flat on the compound miter saw table for a 90° inside corner converts the 45.0° wall half-turn into an exact turntable miter of 35.3° and a saw blade bevel tilt of 30.0° (or 45.0° miter at 0.0° bevel if nested upside-down against the saw fence).

Once sprung against the wall at 45°, this 3-1/4" profile drops 2-5/16" (2.30") vertically down the drywall and projects 2-5/16" (2.30") across the ceiling. Trimming a 32-foot room perimeter with a 15% miter/scarf waste buffer requires 37 linear feet (3 × 16-ft sticks or 4 × 12-ft sticks).

Corner Angle Sensitivity Matrix for 45° Spring Crown Molding

Measured Wall Angle Flat Compound Miter Flat Compound Bevel Nested Upside-Down (0° Bevel)
88° 36.2° 30.6° 46.0° Miter / 0.0° Bevel
90° (Selected) 35.3° 30.0° 45.0° Miter / 0.0° Bevel
92° 34.3° 29.4° 44.0° Miter / 0.0° Bevel
120° 22.2° 20.7° 30.0° Miter / 0.0° Bevel
135° 16.3° 15.7° 22.5° Miter / 0.0° Bevel

4-Piece Inside & Outside Corner Saw Fence Orientation Schedule (90° Corner)

Corner Piece Edge Against Fence Turntable Miter Left Bevel Tilt Keep Side
Inside Left Top (Ceiling) Edge 35.3° Right 30.0° Left Left of Blade
Inside Right Bottom (Wall) Edge 35.3° Left 30.0° Left Right of Blade
Outside Left Bottom (Wall) Edge 35.3° Left 30.0° Left Left of Blade
Outside Right Top (Ceiling) Edge 35.3° Right 30.0° Left Right of Blade

Field Manuals & Code Tables for Crown Molding Calculator

Index of All 107 Manuals →

Frequently Asked Questions (45° Crown @ 90° Inside)

What are the exact flat compound miter and bevel angles for 45° crown molding on a 90° corner?

▼

Laying 45° spring-angle crown flat on your compound miter saw for a 90° inside corner requires setting the turntable miter to 35.3° and tilting the blade bevel to 30.0° (or 45.0° miter at 0.0° bevel if nested upside-down against the fence).

What is the ceiling projection and wall drop witness line for 3-1/4" crown at a 45° spring angle?

▼

A 3-1/4" face-width profile installed at a 45° wall spring angle drops 2-5/16" (2.30") vertically down the wall and projects 2-5/16" (2.30") across the ceiling.

How many 16-ft or 12-ft sticks of crown molding do I need for a 32-ft room perimeter?

▼

Including a 15% compound-miter and corner-scarf waste buffer (37 gross linear feet), order 3 sticks of 16-ft molding (recommended to minimize mid-wall scarf joints) or 4 sticks of 12-ft molding.