Skip to main content
LAYOUTCALCULATOR SCALE 1/16" CAD
AWI Section 6 Finish Trim • SCALE: 1/16" FRACTIONAL
38°/45° Compound Saw Trig Finish Carpentry & Trim

92° Open Corner (38° Crown) — 92° Out-of-Square Open Corner Crown Molding Angles

Eliminate gaping back seams on wide-open 92-degree drywall corners with 38-degree crown molding: exact 30.7° miter and 33.2° compound bevel settings.

Calculation notes
Checked against: AWI Section 6 Finish Trim
Published by LayoutCalculator. Confirm with your local building official.
REV DATE:
Result summary

Framing settlement often opens corners to 92.0° (44.0° half-turn). Reducing your flat saw settings from 31.6°/33.9° down to 30.7° miter and 33.2° bevel closes the front face seam tight.

Typical Field Application

Remodel living rooms, plaster walls, and bowed wood-framed corners exceeding 90 degrees.

Field note

Always divide the digital protractor ceiling reading accurately before dialing in—at 92°, a standard 31.6° detent cut leaves an unsightly open gap at the bottom toe against the wall.

AWI SECTION 6 2D SVG Crown Molding Compound Miter & Bevel Console
Miter 30.7°
Bevel 33.2° L
Fence Check PASS (38°)
92.0° (Inside)
60° (Acute) 88° (Tight) 90° (Square) 135° (Bay)
64 LF (74 LF w/ 15%)
24' (Cabinet) 48' (12x12) 64' (14x18) 200' (Whole Flr)
✓ AWI SECTION 6 COMPOUND SPEC 38°/52° Spring

For a 92.0° inside corner (44.00° half-turn), set miter to 30.7° and bevel to 33.2°. Dry-fit scrap blocks to verify tight face closure.

2D Crown Molding Compound Miter Saw Turntable & Bevel Protractor Blueprint Interactive CAD dial diagram showing exact miter saw turntable swing angle, rear bevel tilt protractor, molding fence orientation, wall drop, and ceiling projection. MITER SWING: 30.7° | BEVEL TILT: 33.2° LEFT | CORNER: 92.0° (INSIDE) FLAT ON SAW TABLE • CEILING/WALL EDGE AT FENCE • SPRING: 38°/52° TOP-DOWN MITER TURNTABLE (30.7°) SAW FENCE (TOP CEILING EDGE FOR INSIDE-L / OUTSIDE-R) CROWN FACE UP (4-1/2") 0° 45° L 45° R Set Miter: 30.7° L / R REAR BEVEL TILT (33.2° LEFT) 0° Tilt Blade 33.2° Left SPRING TRIANGLE (38° WALL / 52° CEILING) Ceil Proj: 2-3/4" Wall Drop: 3-9/16" Face: 4-1/2"
Saw Miter Angle
30.7°
44.0° Half-Turn
Saw Bevel Tilt
33.2°
Left Bevel Tilt
Wall Drop Height
3-9/16"
3.55" Down Wall
Ceil. Projection
2-3/4"
2.77" Across Ceil
16-Ft Trim Sticks
5 Sticks
74 LF (Incl. 15% Waste)

Left vs. Right Piece Saw Fence & Swing Schedule Single-Bevel Left

Follow exact edge-against-fence orientation below so compound miters close tightly at 92.0° corners without reverse-cut scrap:

Crown Molding Left and Right Piece Miter Saw Fence Orientation and Swing Schedule
Corner Piece Edge Against Fence Miter Swing Bevel & Save
Inside Corner — Left Piece Top (Ceiling) Edge at Fence 30.7° RIGHT 33.2° LEFT • Save Left
Inside Corner — Right Piece Bottom (Wall) Edge at Fence 30.7° LEFT 33.2° LEFT • Save Left
Outside Corner — Left Piece Bottom (Wall) Edge at Fence 30.7° LEFT 33.2° LEFT • Save Right
Outside Corner — Right Piece Top (Ceiling) Edge at Fence 30.7° RIGHT 33.2° LEFT • Save Right

Required Bill of Materials (BOM) & Trim Hardware

+15% Miter Waste Included
  • 5 × 16-ft Crown Molding Sticks (4-1/2" Face • 38° Spring) 74 gross LF for 64 LF perimeter (or 7 × 12-ft sticks)
  • 1 × Digital Angle Finder Protractor (±0.1° Stainless Arm) Reads exact 92.0° drywall corner (44.00° half-turn deflection)
  • 15-Gauge 2-1/2" Finish Nails + 2P-10 CA Miter Adhesive Kit AWI Section 6 best practice: pre-glue outside miters on bench and cope inside MDF/pine joints

Independent Field Spec Notice: Compound trigonometric angles and trim waste factors follow AWI Architectural Woodwork Standards Section 6 with zero manufacturer sponsorship.

Need an ad-free Saw Bench Cut Sheet + Vector .SVG protractor?

Pre-Calculated Crown Molding Calculator Blueprints (12 Field Specs)

Select any standard jobsite specification below to load its exact 2D SVG diagram and engineering tables:

Open Base Crown Molding Calculator →
Contractor & Instructor Widget

Embed This 2D SVG Instrument on Your Website (Ad-Free)

Carpentry instructors, trade schools, and builders can embed the standalone ad-free version of this 2D CAD calculator with one HTML snippet.

SPECIFICATION WALKTHROUGH // 92° Open Corner (38° Crown)

Mathematical Derivation & Field Specifications: 92° Open Corner (38° Crown)

Updated • Published by LayoutCalculator

Cutting 38° spring-angle crown molding (4-1/2" face width) flat on the compound miter saw table for a 92° inside corner converts the 44.0° wall half-turn into an exact turntable miter of 30.7° and a saw blade bevel tilt of 33.2° (or 44.0° miter at 0.0° bevel if nested upside-down against the saw fence).

Once sprung against the wall at 38°, this 4-1/2" profile drops 3-9/16" (3.55") vertically down the drywall and projects 2-3/4" (2.77") across the ceiling. Trimming a 64-foot room perimeter with a 15% miter/scarf waste buffer requires 74 linear feet (5 × 16-ft sticks or 7 × 12-ft sticks).

Corner Angle Sensitivity Matrix for 38° Spring Crown Molding

Measured Wall Angle Flat Compound Miter Flat Compound Bevel Nested Upside-Down (0° Bevel)
88° 32.5° 34.5° 46.0° Miter / 0.0° Bevel
90° 31.6° 33.9° 45.0° Miter / 0.0° Bevel
92° (Selected) 30.7° 33.2° 44.0° Miter / 0.0° Bevel
120° 19.6° 23.2° 30.0° Miter / 0.0° Bevel
135° 14.3° 17.6° 22.5° Miter / 0.0° Bevel

4-Piece Inside & Outside Corner Saw Fence Orientation Schedule (92° Corner)

Corner Piece Edge Against Fence Turntable Miter Left Bevel Tilt Keep Side
Inside Left Top (Ceiling) Edge 30.7° Right 33.2° Left Left of Blade
Inside Right Bottom (Wall) Edge 30.7° Left 33.2° Left Right of Blade
Outside Left Bottom (Wall) Edge 30.7° Left 33.2° Left Left of Blade
Outside Right Top (Ceiling) Edge 30.7° Right 33.2° Left Right of Blade

Field Manuals & Code Tables for Crown Molding Calculator

Index of All 107 Manuals →

Frequently Asked Questions (92° Open Corner (38° Crown))

What are the exact flat compound miter and bevel angles for 38° crown molding on a 92° corner?

▼

Laying 38° spring-angle crown flat on your compound miter saw for a 92° inside corner requires setting the turntable miter to 30.7° and tilting the blade bevel to 33.2° (or 44.0° miter at 0.0° bevel if nested upside-down against the fence).

What is the ceiling projection and wall drop witness line for 4-1/2" crown at a 38° spring angle?

▼

A 4-1/2" face-width profile installed at a 38° wall spring angle drops 3-9/16" (3.55") vertically down the wall and projects 2-3/4" (2.77") across the ceiling.

How many 16-ft or 12-ft sticks of crown molding do I need for a 64-ft room perimeter?

▼

Including a 15% compound-miter and corner-scarf waste buffer (74 gross linear feet), order 5 sticks of 16-ft molding (recommended to minimize mid-wall scarf joints) or 7 sticks of 12-ft molding.