Skip to main content
LAYOUTCALCULATOR SCALE 1/16" CAD
AWI Section 6 Finish Trim • SCALE: 1/16" FRACTIONAL
38°/45° Compound Saw Trig Finish Carpentry & Trim

45° Crown @ 135° Bay — 45° Crown Molding on 135° Inside Bay Window Corner

Exact flat compound miter (16.3°) and bevel (15.7°) angles for 45-degree spring crown molding across 135-degree inside bay window and angled walls.

Calculation notes
Checked against: AWI Section 6 Finish Trim
Published by LayoutCalculator. Confirm with your local building official.
REV DATE:
Result summary

For 45°/45° profile crown turning a 135° inside corner (22.5° half-turn), set turntable miter to 16.3° and left blade bevel to 15.7°, with symmetric 3-3/16" wall drop and ceiling projection.

Typical Field Application

Angled kitchen cabinet runs, 135-degree breakfast nook bays, and vaulted ceiling kneewall transitions.

Field note

Shallow 135° inside corners are much easier to flat-miter cleanly than to cope with a coping saw because the back-relief angle is too steep for a thin coping blade.

AWI SECTION 6 2D SVG Crown Molding Compound Miter & Bevel Console
Miter 16.3°
Bevel 15.7° L
Fence Check PASS (45°)
135.0° (Inside)
60° (Acute) 88° (Tight) 90° (Square) 135° (Bay)
52 LF (60 LF w/ 15%)
24' (Cabinet) 48' (12x12) 64' (14x18) 200' (Whole Flr)
✓ AWI SECTION 6 COMPOUND SPEC 45°/45° Spring

For a 135.0° inside corner (22.50° half-turn), set miter to 16.3° and bevel to 15.7°. Dry-fit scrap blocks to verify tight face closure.

2D Crown Molding Compound Miter Saw Turntable & Bevel Protractor Blueprint Interactive CAD dial diagram showing exact miter saw turntable swing angle, rear bevel tilt protractor, molding fence orientation, wall drop, and ceiling projection. MITER SWING: 16.3° | BEVEL TILT: 15.7° LEFT | CORNER: 135.0° (INSIDE) FLAT ON SAW TABLE • CEILING/WALL EDGE AT FENCE • SPRING: 45°/45° TOP-DOWN MITER TURNTABLE (16.3°) SAW FENCE (TOP CEILING EDGE FOR INSIDE-L / OUTSIDE-R) CROWN FACE UP (4-1/2") 0° 45° L 45° R Set Miter: 16.3° L / R REAR BEVEL TILT (15.7° LEFT) 0° Tilt Blade 15.7° Left SPRING TRIANGLE (45° WALL / 45° CEILING) Ceil Proj: 3-3/16" Wall Drop: 3-3/16" Face: 4-1/2"
Saw Miter Angle
16.3°
22.5° Half-Turn
Saw Bevel Tilt
15.7°
Left Bevel Tilt
Wall Drop Height
3-3/16"
3.18" Down Wall
Ceil. Projection
3-3/16"
3.18" Across Ceil
16-Ft Trim Sticks
4 Sticks
60 LF (Incl. 15% Waste)

Left vs. Right Piece Saw Fence & Swing Schedule Single-Bevel Left

Follow exact edge-against-fence orientation below so compound miters close tightly at 135.0° corners without reverse-cut scrap:

Crown Molding Left and Right Piece Miter Saw Fence Orientation and Swing Schedule
Corner Piece Edge Against Fence Miter Swing Bevel & Save
Inside Corner — Left Piece Top (Ceiling) Edge at Fence 16.3° RIGHT 15.7° LEFT • Save Left
Inside Corner — Right Piece Bottom (Wall) Edge at Fence 16.3° LEFT 15.7° LEFT • Save Left
Outside Corner — Left Piece Bottom (Wall) Edge at Fence 16.3° LEFT 15.7° LEFT • Save Right
Outside Corner — Right Piece Top (Ceiling) Edge at Fence 16.3° RIGHT 15.7° LEFT • Save Right

Required Bill of Materials (BOM) & Trim Hardware

+15% Miter Waste Included
  • 4 × 16-ft Crown Molding Sticks (4-1/2" Face • 45° Spring) 60 gross LF for 52 LF perimeter (or 5 × 12-ft sticks)
  • 1 × Digital Angle Finder Protractor (±0.1° Stainless Arm) Reads exact 135.0° drywall corner (22.50° half-turn deflection)
  • 15-Gauge 2-1/2" Finish Nails + 2P-10 CA Miter Adhesive Kit AWI Section 6 best practice: pre-glue outside miters on bench and cope inside MDF/pine joints

Independent Field Spec Notice: Compound trigonometric angles and trim waste factors follow AWI Architectural Woodwork Standards Section 6 with zero manufacturer sponsorship.

Need an ad-free Saw Bench Cut Sheet + Vector .SVG protractor?

Pre-Calculated Crown Molding Calculator Blueprints (12 Field Specs)

Select any standard jobsite specification below to load its exact 2D SVG diagram and engineering tables:

Open Base Crown Molding Calculator →
Contractor & Instructor Widget

Embed This 2D SVG Instrument on Your Website (Ad-Free)

Carpentry instructors, trade schools, and builders can embed the standalone ad-free version of this 2D CAD calculator with one HTML snippet.

SPECIFICATION WALKTHROUGH // 45° Crown @ 135° Bay

Mathematical Derivation & Field Specifications: 45° Crown @ 135° Bay

Updated • Published by LayoutCalculator

Cutting 45° spring-angle crown molding (4-1/2" face width) flat on the compound miter saw table for a 135° inside corner converts the 22.5° wall half-turn into an exact turntable miter of 16.3° and a saw blade bevel tilt of 15.7° (or 22.5° miter at 0.0° bevel if nested upside-down against the saw fence).

Once sprung against the wall at 45°, this 4-1/2" profile drops 3-3/16" (3.18") vertically down the drywall and projects 3-3/16" (3.18") across the ceiling. Trimming a 52-foot room perimeter with a 15% miter/scarf waste buffer requires 60 linear feet (4 × 16-ft sticks or 5 × 12-ft sticks).

Corner Angle Sensitivity Matrix for 45° Spring Crown Molding

Measured Wall Angle Flat Compound Miter Flat Compound Bevel Nested Upside-Down (0° Bevel)
88° 36.2° 30.6° 46.0° Miter / 0.0° Bevel
90° 35.3° 30.0° 45.0° Miter / 0.0° Bevel
92° 34.3° 29.4° 44.0° Miter / 0.0° Bevel
120° 22.2° 20.7° 30.0° Miter / 0.0° Bevel
135° (Selected) 16.3° 15.7° 22.5° Miter / 0.0° Bevel

4-Piece Inside & Outside Corner Saw Fence Orientation Schedule (135° Corner)

Corner Piece Edge Against Fence Turntable Miter Left Bevel Tilt Keep Side
Inside Left Top (Ceiling) Edge 16.3° Right 15.7° Left Left of Blade
Inside Right Bottom (Wall) Edge 16.3° Left 15.7° Left Right of Blade
Outside Left Bottom (Wall) Edge 16.3° Left 15.7° Left Left of Blade
Outside Right Top (Ceiling) Edge 16.3° Right 15.7° Left Right of Blade

Field Manuals & Code Tables for Crown Molding Calculator

Index of All 107 Manuals →

Frequently Asked Questions (45° Crown @ 135° Bay)

What are the exact flat compound miter and bevel angles for 45° crown molding on a 135° corner?

▼

Laying 45° spring-angle crown flat on your compound miter saw for a 135° inside corner requires setting the turntable miter to 16.3° and tilting the blade bevel to 15.7° (or 22.5° miter at 0.0° bevel if nested upside-down against the fence).

What is the ceiling projection and wall drop witness line for 4-1/2" crown at a 45° spring angle?

▼

A 4-1/2" face-width profile installed at a 45° wall spring angle drops 3-3/16" (3.18") vertically down the wall and projects 3-3/16" (3.18") across the ceiling.

How many 16-ft or 12-ft sticks of crown molding do I need for a 52-ft room perimeter?

▼

Including a 15% compound-miter and corner-scarf waste buffer (60 gross linear feet), order 4 sticks of 16-ft molding (recommended to minimize mid-wall scarf joints) or 5 sticks of 12-ft molding.