Skip to main content
LAYOUTCALCULATOR SCALE 1/16" CAD
AWI Section 6 Finish Trim • SCALE: 1/16" FRACTIONAL
38°/45° Compound Saw Trig Finish Carpentry & Trim

45° Cabinet Crown @ 90° — 45° Cabinet Crown Molding: 90° Miter & Bevel Cuts

Compound saw settings for 45-degree traditional and kitchen cabinet crown molding (45/45) at 90-degree outside corners: 35.3° miter and 30.0° bevel.

Calculation notes
Checked against: AWI Section 6 Finish Trim
Published by LayoutCalculator. Confirm with your local building official.
REV DATE:
Result summary

Symmetric 45°/45° cabinet crown laid flat on the saw table requires a 35.3° (35.26°) miter swing and an exact 30.0° left bevel tilt, projecting 2-5/16" vertically and horizontally for 3-1/4" trim.

Typical Field Application

Kitchen upper wall cabinets, built-in bookcases, fireplace mantels, and furniture-grade hardwood cornices.

Field note

Pre-assemble outside cabinet crown corners flat on your workbench using two-part cyanoacrylate (CA) miter glue and activator before lifting the completed L-return onto the cabinet nailer.

AWI SECTION 6 2D SVG Crown Molding Compound Miter & Bevel Console
Miter 35.3°
Bevel 30.0° L
Fence Check PASS (45°)
90.0° (Outside)
60° (Acute) 88° (Tight) 90° (Square) 135° (Bay)
24 LF (28 LF w/ 15%)
24' (Cabinet) 48' (12x12) 64' (14x18) 200' (Whole Flr)
✓ MATCHES SAW CROWN DETENT STOP 45°/45° Spring

Exact 35.3° miter and 30.0° left bevel lock directly into factory crown detents on DeWalt, Makita, Bosch, and Milwaukee saws.

2D Crown Molding Compound Miter Saw Turntable & Bevel Protractor Blueprint Interactive CAD dial diagram showing exact miter saw turntable swing angle, rear bevel tilt protractor, molding fence orientation, wall drop, and ceiling projection. MITER SWING: 35.3° | BEVEL TILT: 30.0° LEFT | CORNER: 90.0° (OUTSIDE) FLAT ON SAW TABLE • CEILING/WALL EDGE AT FENCE • SPRING: 45°/45° TOP-DOWN MITER TURNTABLE (35.3°) SAW FENCE (TOP CEILING EDGE FOR INSIDE-L / OUTSIDE-R) CROWN FACE UP (3-1/4") 0° 45° L 45° R Set Miter: 35.3° L / R (Crown Detent) REAR BEVEL TILT (30.0° LEFT) 0° Tilt Blade 30.0° Left SPRING TRIANGLE (45° WALL / 45° CEILING) Ceil Proj: 2-5/16" Wall Drop: 2-5/16" Face: 3-1/4"
Saw Miter Angle
35.3°
Crown Detent Stop
Saw Bevel Tilt
30.0°
Left Bevel Tilt
Wall Drop Height
2-5/16"
2.30" Down Wall
Ceil. Projection
2-5/16"
2.30" Across Ceil
16-Ft Trim Sticks
2 Sticks
28 LF (Incl. 15% Waste)

Left vs. Right Piece Saw Fence & Swing Schedule Single-Bevel Left

Follow exact edge-against-fence orientation below so compound miters close tightly at 90.0° corners without reverse-cut scrap:

Crown Molding Left and Right Piece Miter Saw Fence Orientation and Swing Schedule
Corner Piece Edge Against Fence Miter Swing Bevel & Save
Inside Corner — Left Piece Top (Ceiling) Edge at Fence 35.3° RIGHT 30.0° LEFT • Save Left
Inside Corner — Right Piece Bottom (Wall) Edge at Fence 35.3° LEFT 30.0° LEFT • Save Left
Outside Corner — Left Piece Bottom (Wall) Edge at Fence 35.3° LEFT 30.0° LEFT • Save Right
Outside Corner — Right Piece Top (Ceiling) Edge at Fence 35.3° RIGHT 30.0° LEFT • Save Right

Required Bill of Materials (BOM) & Trim Hardware

+15% Miter Waste Included
  • 2 × 16-ft Crown Molding Sticks (3-1/4" Face • 45° Spring) 28 gross LF for 24 LF perimeter (or 3 × 12-ft sticks)
  • 1 × Digital Angle Finder Protractor (±0.1° Stainless Arm) Reads exact 90.0° drywall corner (45.00° half-turn deflection)
  • 15-Gauge 2-1/2" Finish Nails + 2P-10 CA Miter Adhesive Kit AWI Section 6 best practice: pre-glue outside miters on bench and cope inside MDF/pine joints

Independent Field Spec Notice: Compound trigonometric angles and trim waste factors follow AWI Architectural Woodwork Standards Section 6 with zero manufacturer sponsorship.

Need an ad-free Saw Bench Cut Sheet + Vector .SVG protractor?

Pre-Calculated Crown Molding Calculator Blueprints (12 Field Specs)

Select any standard jobsite specification below to load its exact 2D SVG diagram and engineering tables:

Open Base Crown Molding Calculator →
Contractor & Instructor Widget

Embed This 2D SVG Instrument on Your Website (Ad-Free)

Carpentry instructors, trade schools, and builders can embed the standalone ad-free version of this 2D CAD calculator with one HTML snippet.

SPECIFICATION WALKTHROUGH // 45° Cabinet Crown @ 90°

Mathematical Derivation & Field Specifications: 45° Cabinet Crown @ 90°

Updated • Published by LayoutCalculator

Cutting 45° spring-angle crown molding (3-1/4" face width) flat on the compound miter saw table for a 90° outside corner converts the 45.0° wall half-turn into an exact turntable miter of 35.3° and a saw blade bevel tilt of 30.0° (or 45.0° miter at 0.0° bevel if nested upside-down against the saw fence).

Once sprung against the wall at 45°, this 3-1/4" profile drops 2-5/16" (2.30") vertically down the drywall and projects 2-5/16" (2.30") across the ceiling. Trimming a 24-foot room perimeter with a 15% miter/scarf waste buffer requires 28 linear feet (2 × 16-ft sticks or 3 × 12-ft sticks).

Corner Angle Sensitivity Matrix for 45° Spring Crown Molding

Measured Wall Angle Flat Compound Miter Flat Compound Bevel Nested Upside-Down (0° Bevel)
88° 36.2° 30.6° 46.0° Miter / 0.0° Bevel
90° (Selected) 35.3° 30.0° 45.0° Miter / 0.0° Bevel
92° 34.3° 29.4° 44.0° Miter / 0.0° Bevel
120° 22.2° 20.7° 30.0° Miter / 0.0° Bevel
135° 16.3° 15.7° 22.5° Miter / 0.0° Bevel

4-Piece Inside & Outside Corner Saw Fence Orientation Schedule (90° Corner)

Corner Piece Edge Against Fence Turntable Miter Left Bevel Tilt Keep Side
Inside Left Top (Ceiling) Edge 35.3° Right 30.0° Left Left of Blade
Inside Right Bottom (Wall) Edge 35.3° Left 30.0° Left Right of Blade
Outside Left Bottom (Wall) Edge 35.3° Left 30.0° Left Left of Blade
Outside Right Top (Ceiling) Edge 35.3° Right 30.0° Left Right of Blade

Field Manuals & Code Tables for Crown Molding Calculator

Index of All 107 Manuals →

Frequently Asked Questions (45° Cabinet Crown @ 90°)

What are the exact flat compound miter and bevel angles for 45° crown molding on a 90° corner?

▼

Laying 45° spring-angle crown flat on your compound miter saw for a 90° outside corner requires setting the turntable miter to 35.3° and tilting the blade bevel to 30.0° (or 45.0° miter at 0.0° bevel if nested upside-down against the fence).

What is the ceiling projection and wall drop witness line for 3-1/4" crown at a 45° spring angle?

▼

A 3-1/4" face-width profile installed at a 45° wall spring angle drops 2-5/16" (2.30") vertically down the wall and projects 2-5/16" (2.30") across the ceiling.

How many 16-ft or 12-ft sticks of crown molding do I need for a 24-ft room perimeter?

▼

Including a 15% compound-miter and corner-scarf waste buffer (28 gross linear feet), order 2 sticks of 16-ft molding (recommended to minimize mid-wall scarf joints) or 3 sticks of 12-ft molding.