Skip to main content
LAYOUTCALCULATOR SCALE 1/16" CAD
AWI Section 6 Finish Trim • SCALE: 1/16" FRACTIONAL
38°/45° Compound Saw Trig Finish Carpentry & Trim

88° Out-of-Square Corner — Out-of-Square 88° Corner Crown Molding Miter/Bevel

Solve tight out-of-square 88-degree drywall inside corners for 38-degree crown molding: 32.5° miter and 34.5° bevel compound cuts with zero face gap.

Calculation notes
Checked against: AWI Section 6 Finish Trim
Published by LayoutCalculator. Confirm with your local building official.
REV DATE:
Result summary

Tape-and-mud buildup routinely pinches inside corners down to 88.0° (46.0° half-turn). Compensating on the saw requires a 32.5° miter and 34.5° left bevel instead of standard 31.6°/33.9° detents.

Typical Field Application

Older remodel rooms, taped drywall inside corners with heavy mud buildup, and wide 5-1/4" stained wood cornices.

Field note

On stained hardwood crown where caulk cannot hide an open seam, measure every corner at ceiling height with a digital protractor and test-fit two 8-inch scrap blocks before cutting full sticks.

AWI SECTION 6 2D SVG Crown Molding Compound Miter & Bevel Console
Miter 32.5°
Bevel 34.5° L
Fence Check PASS (38°)
88.0° (Inside)
60° (Acute) 88° (Tight) 90° (Square) 135° (Bay)
64 LF (74 LF w/ 15%)
24' (Cabinet) 48' (12x12) 64' (14x18) 200' (Whole Flr)
✓ AWI SECTION 6 COMPOUND SPEC 38°/52° Spring

For a 88.0° inside corner (46.00° half-turn), set miter to 32.5° and bevel to 34.5°. Dry-fit scrap blocks to verify tight face closure.

2D Crown Molding Compound Miter Saw Turntable & Bevel Protractor Blueprint Interactive CAD dial diagram showing exact miter saw turntable swing angle, rear bevel tilt protractor, molding fence orientation, wall drop, and ceiling projection. MITER SWING: 32.5° | BEVEL TILT: 34.5° LEFT | CORNER: 88.0° (INSIDE) FLAT ON SAW TABLE • CEILING/WALL EDGE AT FENCE • SPRING: 38°/52° TOP-DOWN MITER TURNTABLE (32.5°) SAW FENCE (TOP CEILING EDGE FOR INSIDE-L / OUTSIDE-R) CROWN FACE UP (5-1/4") 0° 45° L 45° R Set Miter: 32.5° L / R REAR BEVEL TILT (34.5° LEFT) 0° Tilt Blade 34.5° Left SPRING TRIANGLE (38° WALL / 52° CEILING) Ceil Proj: 3-1/4" Wall Drop: 4-1/8" Face: 5-1/4"
Saw Miter Angle
32.5°
46.0° Half-Turn
Saw Bevel Tilt
34.5°
Left Bevel Tilt
Wall Drop Height
4-1/8"
4.14" Down Wall
Ceil. Projection
3-1/4"
3.23" Across Ceil
16-Ft Trim Sticks
5 Sticks
74 LF (Incl. 15% Waste)

Left vs. Right Piece Saw Fence & Swing Schedule Single-Bevel Left

Follow exact edge-against-fence orientation below so compound miters close tightly at 88.0° corners without reverse-cut scrap:

Crown Molding Left and Right Piece Miter Saw Fence Orientation and Swing Schedule
Corner Piece Edge Against Fence Miter Swing Bevel & Save
Inside Corner — Left Piece Top (Ceiling) Edge at Fence 32.5° RIGHT 34.5° LEFT • Save Left
Inside Corner — Right Piece Bottom (Wall) Edge at Fence 32.5° LEFT 34.5° LEFT • Save Left
Outside Corner — Left Piece Bottom (Wall) Edge at Fence 32.5° LEFT 34.5° LEFT • Save Right
Outside Corner — Right Piece Top (Ceiling) Edge at Fence 32.5° RIGHT 34.5° LEFT • Save Right

Required Bill of Materials (BOM) & Trim Hardware

+15% Miter Waste Included
  • 5 × 16-ft Crown Molding Sticks (5-1/4" Face • 38° Spring) 74 gross LF for 64 LF perimeter (or 7 × 12-ft sticks)
  • 1 × Digital Angle Finder Protractor (±0.1° Stainless Arm) Reads exact 88.0° drywall corner (46.00° half-turn deflection)
  • 15-Gauge 2-1/2" Finish Nails + 2P-10 CA Miter Adhesive Kit AWI Section 6 best practice: pre-glue outside miters on bench and cope inside MDF/pine joints

Independent Field Spec Notice: Compound trigonometric angles and trim waste factors follow AWI Architectural Woodwork Standards Section 6 with zero manufacturer sponsorship.

Need an ad-free Saw Bench Cut Sheet + Vector .SVG protractor?

Pre-Calculated Crown Molding Calculator Blueprints (12 Field Specs)

Select any standard jobsite specification below to load its exact 2D SVG diagram and engineering tables:

Open Base Crown Molding Calculator →
Contractor & Instructor Widget

Embed This 2D SVG Instrument on Your Website (Ad-Free)

Carpentry instructors, trade schools, and builders can embed the standalone ad-free version of this 2D CAD calculator with one HTML snippet.

SPECIFICATION WALKTHROUGH // 88° Out-of-Square Corner

Mathematical Derivation & Field Specifications: 88° Out-of-Square Corner

Updated • Published by LayoutCalculator

Cutting 38° spring-angle crown molding (5-1/4" face width) flat on the compound miter saw table for a 88° inside corner converts the 46.0° wall half-turn into an exact turntable miter of 32.5° and a saw blade bevel tilt of 34.5° (or 46.0° miter at 0.0° bevel if nested upside-down against the saw fence).

Once sprung against the wall at 38°, this 5-1/4" profile drops 4-1/8" (4.14") vertically down the drywall and projects 3-1/4" (3.23") across the ceiling. Trimming a 64-foot room perimeter with a 15% miter/scarf waste buffer requires 74 linear feet (5 × 16-ft sticks or 7 × 12-ft sticks).

Corner Angle Sensitivity Matrix for 38° Spring Crown Molding

Measured Wall Angle Flat Compound Miter Flat Compound Bevel Nested Upside-Down (0° Bevel)
88° (Selected) 32.5° 34.5° 46.0° Miter / 0.0° Bevel
90° 31.6° 33.9° 45.0° Miter / 0.0° Bevel
92° 30.7° 33.2° 44.0° Miter / 0.0° Bevel
120° 19.6° 23.2° 30.0° Miter / 0.0° Bevel
135° 14.3° 17.6° 22.5° Miter / 0.0° Bevel

4-Piece Inside & Outside Corner Saw Fence Orientation Schedule (88° Corner)

Corner Piece Edge Against Fence Turntable Miter Left Bevel Tilt Keep Side
Inside Left Top (Ceiling) Edge 32.5° Right 34.5° Left Left of Blade
Inside Right Bottom (Wall) Edge 32.5° Left 34.5° Left Right of Blade
Outside Left Bottom (Wall) Edge 32.5° Left 34.5° Left Left of Blade
Outside Right Top (Ceiling) Edge 32.5° Right 34.5° Left Right of Blade

Field Manuals & Code Tables for Crown Molding Calculator

Index of All 107 Manuals →

Frequently Asked Questions (88° Out-of-Square Corner)

What are the exact flat compound miter and bevel angles for 38° crown molding on a 88° corner?

▼

Laying 38° spring-angle crown flat on your compound miter saw for a 88° inside corner requires setting the turntable miter to 32.5° and tilting the blade bevel to 34.5° (or 46.0° miter at 0.0° bevel if nested upside-down against the fence).

What is the ceiling projection and wall drop witness line for 5-1/4" crown at a 38° spring angle?

▼

A 5-1/4" face-width profile installed at a 38° wall spring angle drops 4-1/8" (4.14") vertically down the wall and projects 3-1/4" (3.23") across the ceiling.

How many 16-ft or 12-ft sticks of crown molding do I need for a 64-ft room perimeter?

▼

Including a 15% compound-miter and corner-scarf waste buffer (74 gross linear feet), order 5 sticks of 16-ft molding (recommended to minimize mid-wall scarf joints) or 7 sticks of 12-ft molding.