Skip to main content
LAYOUTCALCULATOR SCALE 1/16" CAD
2024 IRC Section R802 • SCALE: 1/16" FRACTIONAL
IRC R802 Birdsmouth Check Framing & Carpentry

10-Ft Porch (3/12 Pitch) — 10-Ft Porch Rafter Layout: 3/12 Low-Slope 2x6 Cuts

Low-slope 10-ft gable porch roof rafter plan at 3/12 pitch: 5 ft 1-1/16 in line length, 14.0° plumb cut, 12" soffit tail, and 8-ft 2x6 lumber count.

Calculation notes
Checked against: 2024 IRC Section R802
Published by LayoutCalculator. Confirm with your local building official.
REV DATE:
Result summary

Deducting half of a 1-1/2" ridge leaves a 59-1/4" adjusted run. At 3/12 pitch (14.0°), ridge-to-heel length is 5 ft 1-1/16 in plus a 12-3/8" tail (6 ft 1-7/16 in total—order 29 × 8-ft 2x6s).

Typical Field Application

Covered front entry porches, grill shelters, firewood sheds, and low-clearance patio roofs.

Field note

Under IRC R905.2.2, 3/12 is the absolute minimum slope for asphalt shingles and requires double-layer underlayment or full self-adhering ice-and-water membrane across the deck.

IRC R802.4 & R802.7 2D SVG Roof Rafter & Birdsmouth Drafting Console
Line Len 5' 1-1/16"
HAP 4-13/16"
IRC R802 PASS (3/12)
10' (120")
8' (Shed) 16' (1-Car) 24' (2-Car) 48' (Barn)
3/12 (14.0°)
3/12 (Low) 6/12 (Ranch) 9/12 (Steep) 12/12 (45°)
12" Horiz
✓ PASSES 2024 IRC R802.7.1 NOTCH LIMIT 14.0° Plumb

3-1/2" full plate bearing produces a 7/8" perpendicular notch (≤ 1-13/16" max D/3 limit for 2x6). HAP is 4-13/16".

2D IRC R802 Roof Rafter Span, Rise, Line Length & Birdsmouth HAP Blueprint Interactive scale CAD drawing of a gable roof framing cross-section showing exterior walls, ridge board deduction, common rafter line length, soffit tail, collar tie zone, and birdsmouth Height Above Plate. COLLAR TIE (UPPER 1/3) Rise: 1' 2-13/16" Net Run: 4' 11-1/4" Building Span: 10' 0" (120") + 12" Soffits PITCH: 3/12 (14.0°) | LINE: 5' 1-1/16" Total Cut w/ Tail: 6' 1-7/16" • HAP: 4-13/16"
Rafter Line Len
5' 1-1/16"
Run: 59-1/4"
Total Cut + Tail
6' 1-7/16"
Buy 8-ft 2x6
Height Above Plate
4-13/16"
Heel Cut: 7/8"
Plumb / Seat Angle
14.0° / 76.0°
Rise: 1' 2-13/16"
Total Rafters
26 pcs
13/side @ 16" OC

Hooked Tape-Measure Rafter Layout Schedule 12.37" / ft Run

Cut the ridge plumb angle at the top tip (0"), hook your tape on the long point of the crown edge, and pull down the board:

Cumulative Hooked Tape-Measure Marks Along Roof Rafter Top Edge
Layout Station Cumulative Mark Shop Saw / Square Spec
1. Ridge Plumb Cut (Peak) 0" (Hook Board Tip) 14.0° Miter Angle
2. Collar Tie Zone (Upper 1/3) 20-3/8" (20.36") IRC R802.4.6 Strap Limit
3. Birdsmouth Heel Plumb Line 61-1/16" (5' 1-1/16") HAP: 4-13/16"
4. Birdsmouth Level Seat Cut 3-1/2" Level Bearing 76.0° Seat • 7/8" Heel
5. Fascia Soffit Tail Plumb Cut 73-7/16" (6' 1-7/16") Tail: +12-3/8"

Required Bill of Materials (BOM) & Hardware

Auto-Calculated Quantities
  • 26 × 8-ft 2x6 #2 Kiln-Dried Framing Rafters 13 rafters per slope @ 16" OC across 16-ft ridge
  • 7 Sheets × 4x8 (7/16" or 5/8") APA Structural Roof Sheathing Covers 196 sq ft sloped roof deck (+10% gable/starter waste)
  • 26 × Simpson Strong-Tie H2.5A Hurricane Rafter Ties Plus 5 × 1x6/2x4 Collar Ties (4ft OC) & 1 × 16-ft Ridge Boards

Independent Field Spec Notice: Geometry and birdsmouth notch limits follow 2024 IRC Sections R802.4, R802.6, and R802.7.1. Verify snow-load lumber spans against local R802.4.1 tables.

Need full-scale Jobsite Cut Sheet + Vector .SVG blueprint?

Pre-Calculated Roof Rafter Calculator Blueprints (12 Field Specs)

Select any standard jobsite specification below to load its exact 2D SVG diagram and engineering tables:

Open Base Roof Rafter Calculator →
Contractor & Instructor Widget

Embed This 2D SVG Instrument on Your Website (Ad-Free)

Carpentry instructors, trade schools, and builders can embed the standalone ad-free version of this 2D CAD calculator with one HTML snippet.

SPECIFICATION WALKTHROUGH // 10-Ft Porch (3/12 Pitch)

Mathematical Derivation & Field Specifications: 10-Ft Porch (3/12 Pitch)

Updated • Published by LayoutCalculator

For a 10-foot (120") building width framed at a 3/12 roof pitch (14.0° slope) with a 1.5" ridge board, subtracting half the ridge thickness per side leaves an adjusted horizontal run of 59-1/4" (59.25"). Multiplying by the unit secant factor 1.0308 establishes a ridge-to-heel line length of 5' 1-1/16" (61.07") and a ridge peak rise of 14.8" (1.23 ft) above the wall plate.

Adding a 12" horizontal eave projection contributes 12-3/8" of sloped tail stock, bringing overall cut length to 6' 1-7/16" (order 8-ft 2x6 boards). Per 2024 IRC Section R802.7.1, birdsmouth end notches on 2x6 (5.5" actual depth) must not exceed 1-13/16" (D/3), preserving a 4-13/16" Height Above Plate (HAP) across all 29 rafters (13 pairs @ 16" OC + 10% cull).

Roof Pitch Sensitivity Matrix for 10-Ft Building Span (12" Overhang)

Roof Pitch Plumb Cut Angle Secant Factor Main Line Length Total w/ Overhang Min Lumber Stock
4/12 18.4° 1.0541 5' 2-7/16" 6' 3-1/8" 8 ft 2x6
6/12 26.6° 1.1180 5' 6-1/4" 6' 7-11/16" 8 ft 2x6
8/12 33.7° 1.2019 5' 11-3/16" 7' 1-5/8" 8 ft 2x6
10/12 39.8° 1.3017 6' 5-1/8" 7' 8-3/4" 8 ft 2x6
12/12 45.0° 1.4142 6' 11-13/16" 8' 4-3/4" 10 ft 2x6

Pattern Rafter Scribe & Saw Layout Checkpoints (2x6 @ 3/12)

Checkpoint Hooked Tape / Angle Code / Framing Rule
1. Ridge Plumb Cut 0" Origin • 14.0° Miter Crown edge facing UP; deduct 0.75" half-ridge
2. Birdsmouth Heel Plumb 5' 1-1/16" (61.07") HAP = 4-13/16" above top plate; 3-1/2" level seat
3. Fascia Tail Plumb Cut 6' 1-7/16" (73.44") 12" horizontal soffit projection (14.0° plumb)

Official Building Code & Industry Standard Citations

Field Manuals & Code Tables for Roof Rafter Calculator

Index of All 107 Manuals →

Frequently Asked Questions (10-Ft Porch (3/12 Pitch))

What is the exact rafter line length and plumb cut angle for a 10-ft span at 3/12 pitch?

▼

Deducting half of a 1.5" ridge board from a 10-ft (120") building width leaves an adjusted horizontal run of 59-1/4". At 3/12 pitch (14.0° plumb cut, 76.0° seat cut), ridge-to-heel line length is 5' 1-1/16" (61.07") plus a 12-3/8" overhang tail (6' 1-7/16" overall).

What is the maximum birdsmouth notch depth allowed by IRC R802.7.1 on 2x6 rafters?

▼

Under 2024 IRC Section R802.7.1, an end-bearing birdsmouth notch cannot exceed one-third (D/3) of the actual rafter depth. For 2x6 lumber (5.5" actual depth), maximum notch depth is 1-13/16", preserving a 4-13/16" Height Above Plate (HAP).

What lumber length and quantity should I order for a 10' × 16' gable roof at 16" OC?

▼

Each 6' 1-7/16" common rafter requires 8-foot 2x6 stock. Across a 16-foot roof ridge at 16" on-center (13 rafter pairs), order 29 boards including a 10% culling buffer.