Skip to main content
LAYOUTCALCULATOR SCALE 1/16" CAD
2024 IRC Section R802 • SCALE: 1/16" FRACTIONAL
IRC R802 Birdsmouth Check Framing & Carpentry

20-Ft Garage (4/12 Pitch) — 20-Ft Garage Roof Rafters: 4/12 Pitch 2x8 Framing

20-ft detached garage rafter layout at 4/12 roof pitch: 10 ft 5-11/16 in line length, 18.4° plumb cut, 16" soffit eave, and 12-ft 2x8 stock quantity.

Calculation notes
Checked against: 2024 IRC Section R802
Published by LayoutCalculator. Confirm with your local building official.
REV DATE:
Result summary

A 119-1/4" adjusted run at 4/12 pitch (18.4°) yields a 10 ft 5-11/16 in line length plus a 16-7/8" soffit tail (11 ft 10-9/16 in overall), maximizing standard 12-ft 2x8 stock (42 boards).

Typical Field Application

20x24 two-car garages, mid-century ranch additions, and low-profile municipal height-restricted builds.

Field note

Shallow 4/12 rafters exert higher outward horizontal thrust at the wall plates than steep pitches—nail ceiling joists directly alongside every rafter heel per IRC Table R802.5.2.

IRC R802.4 & R802.7 2D SVG Roof Rafter & Birdsmouth Drafting Console
Line Len 10' 5-11/16"
HAP 6-1/2"
IRC R802 PASS (4/12)
20' (240")
8' (Shed) 16' (1-Car) 24' (2-Car) 48' (Barn)
4/12 (18.4°)
3/12 (Low) 6/12 (Ranch) 9/12 (Steep) 12/12 (45°)
16" Horiz
✓ PASSES 2024 IRC R802.7.1 NOTCH LIMIT 18.4° Plumb

3-1/2" full plate bearing produces a 1-1/8" perpendicular notch (≤ 2-7/16" max D/3 limit for 2x8). HAP is 6-1/2".

2D IRC R802 Roof Rafter Span, Rise, Line Length & Birdsmouth HAP Blueprint Interactive scale CAD drawing of a gable roof framing cross-section showing exterior walls, ridge board deduction, common rafter line length, soffit tail, collar tie zone, and birdsmouth Height Above Plate. COLLAR TIE (UPPER 1/3) Rise: 3' 3-3/4" Net Run: 9' 11-1/4" Building Span: 20' 0" (240") + 16" Soffits PITCH: 4/12 (18.4°) | LINE: 10' 5-11/16" Total Cut w/ Tail: 11' 10-9/16" • HAP: 6-1/2"
Rafter Line Len
10' 5-11/16"
Run: 119-1/4"
Total Cut + Tail
11' 10-9/16"
Buy 12-ft 2x8
Height Above Plate
6-1/2"
Heel Cut: 1-3/16"
Plumb / Seat Angle
18.4° / 71.6°
Rise: 3' 3-3/4"
Total Rafters
38 pcs
19/side @ 16" OC

Hooked Tape-Measure Rafter Layout Schedule 12.65" / ft Run

Cut the ridge plumb angle at the top tip (0"), hook your tape on the long point of the crown edge, and pull down the board:

Cumulative Hooked Tape-Measure Marks Along Roof Rafter Top Edge
Layout Station Cumulative Mark Shop Saw / Square Spec
1. Ridge Plumb Cut (Peak) 0" (Hook Board Tip) 18.4° Miter Angle
2. Collar Tie Zone (Upper 1/3) 41-7/8" (41.90") IRC R802.4.6 Strap Limit
3. Birdsmouth Heel Plumb Line 125-11/16" (10' 5-11/16") HAP: 6-1/2"
4. Birdsmouth Level Seat Cut 3-1/2" Level Bearing 71.6° Seat • 1-3/16" Heel
5. Fascia Soffit Tail Plumb Cut 142-9/16" (11' 10-9/16") Tail: +16-7/8"

Required Bill of Materials (BOM) & Hardware

Auto-Calculated Quantities
  • 38 × 12-ft 2x8 #2 Kiln-Dried Framing Rafters 19 rafters per slope @ 16" OC across 24-ft ridge
  • 20 Sheets × 4x8 (7/16" or 5/8") APA Structural Roof Sheathing Covers 570 sq ft sloped roof deck (+10% gable/starter waste)
  • 38 × Simpson Strong-Tie H2.5A Hurricane Rafter Ties Plus 7 × 1x6/2x4 Collar Ties (4ft OC) & 2 × 16-ft Ridge Boards

Independent Field Spec Notice: Geometry and birdsmouth notch limits follow 2024 IRC Sections R802.4, R802.6, and R802.7.1. Verify snow-load lumber spans against local R802.4.1 tables.

Need full-scale Jobsite Cut Sheet + Vector .SVG blueprint?

Pre-Calculated Roof Rafter Calculator Blueprints (12 Field Specs)

Select any standard jobsite specification below to load its exact 2D SVG diagram and engineering tables:

Open Base Roof Rafter Calculator →
Contractor & Instructor Widget

Embed This 2D SVG Instrument on Your Website (Ad-Free)

Carpentry instructors, trade schools, and builders can embed the standalone ad-free version of this 2D CAD calculator with one HTML snippet.

SPECIFICATION WALKTHROUGH // 20-Ft Garage (4/12 Pitch)

Mathematical Derivation & Field Specifications: 20-Ft Garage (4/12 Pitch)

Updated • Published by LayoutCalculator

For a 20-foot (240") building width framed at a 4/12 roof pitch (18.4° slope) with a 1.5" ridge board, subtracting half the ridge thickness per side leaves an adjusted horizontal run of 119-1/4" (119.25"). Multiplying by the unit secant factor 1.0541 establishes a ridge-to-heel line length of 10' 5-11/16" (125.70") and a ridge peak rise of 39.8" (3.31 ft) above the wall plate.

Adding a 16" horizontal eave projection contributes 16-7/8" of sloped tail stock, bringing overall cut length to 11' 10-9/16" (order 12-ft 2x8 boards). Per 2024 IRC Section R802.7.1, birdsmouth end notches on 2x8 (7.25" actual depth) must not exceed 2-7/16" (D/3), preserving a 6-1/2" Height Above Plate (HAP) across all 42 rafters (19 pairs @ 16" OC + 10% cull).

Roof Pitch Sensitivity Matrix for 20-Ft Building Span (16" Overhang)

Roof Pitch Plumb Cut Angle Secant Factor Main Line Length Total w/ Overhang Min Lumber Stock
4/12 (Selected) 18.4° 1.0541 10' 5-11/16" 11' 10-9/16" 12 ft 2x8
6/12 26.6° 1.1180 11' 1-5/16" 12' 7-3/16" 14 ft 2x8
8/12 33.7° 1.2019 11' 11-5/16" 13' 6-9/16" 14 ft 2x8
10/12 39.8° 1.3017 12' 11-1/4" 14' 8-1/16" 16 ft 2x8
12/12 45.0° 1.4142 14' 5/8" 15' 11-1/4" 16 ft 2x8

Pattern Rafter Scribe & Saw Layout Checkpoints (2x8 @ 4/12)

Checkpoint Hooked Tape / Angle Code / Framing Rule
1. Ridge Plumb Cut 0" Origin • 18.4° Miter Crown edge facing UP; deduct 0.75" half-ridge
2. Birdsmouth Heel Plumb 10' 5-11/16" (125.70") HAP = 6-1/2" above top plate; 3-1/2" level seat
3. Fascia Tail Plumb Cut 11' 10-9/16" (142.57") 16" horizontal soffit projection (18.4° plumb)

Official Building Code & Industry Standard Citations

Field Manuals & Code Tables for Roof Rafter Calculator

Index of All 107 Manuals →

Frequently Asked Questions (20-Ft Garage (4/12 Pitch))

What is the exact rafter line length and plumb cut angle for a 20-ft span at 4/12 pitch?

▼

Deducting half of a 1.5" ridge board from a 20-ft (240") building width leaves an adjusted horizontal run of 119-1/4". At 4/12 pitch (18.4° plumb cut, 71.6° seat cut), ridge-to-heel line length is 10' 5-11/16" (125.70") plus a 16-7/8" overhang tail (11' 10-9/16" overall).

What is the maximum birdsmouth notch depth allowed by IRC R802.7.1 on 2x8 rafters?

▼

Under 2024 IRC Section R802.7.1, an end-bearing birdsmouth notch cannot exceed one-third (D/3) of the actual rafter depth. For 2x8 lumber (7.25" actual depth), maximum notch depth is 2-7/16", preserving a 6-1/2" Height Above Plate (HAP).

What lumber length and quantity should I order for a 20' × 24' gable roof at 16" OC?

▼

Each 11' 10-9/16" common rafter requires 12-foot 2x8 stock. Across a 24-foot roof ridge at 16" on-center (19 rafter pairs), order 42 boards including a 10% culling buffer.