Skip to main content
LAYOUTCALCULATOR SCALE 1/16" CAD
2024 IRC Section R802 • SCALE: 1/16" FRACTIONAL
IRC R802 Birdsmouth Check Framing & Carpentry

30-Ft Barn (9/12 Pitch) — 30-Ft Barn Rafter Layout: 9/12 Pitch 2x12 LVL Ridge

Heavy 30-ft gable barn rafter blueprint at 9/12 pitch with 1-3/4" LVL ridge: 18 ft 7-15/16 in line length, 36.9° plumb cut, and 22-ft 2x12 sizing.

Calculation notes
Checked against: 2024 IRC Section R802
Published by LayoutCalculator. Confirm with your local building official.
REV DATE:
Result summary

Deducting half of a 1-3/4" structural LVL ridge leaves a 179-1/8" run. At 9/12 pitch (36.9°, 3-4-5 triangle), line length is 18 ft 7-15/16 in plus a 22-1/2" tail (20 ft 6-7/16 in—order 22-ft 2x12s).

Typical Field Application

30x40 timber barns, vaulted great rooms with structural LVL ridge beams, and bonus-room attic roofs.

Field note

9/12 is an exact 3-4-5 triangle (secant factor 1.2500)—use face-mount joist hangers rated for sloped 2x12 rafters when framing flush into a structural 1-3/4" LVL ridge beam.

IRC R802.4 & R802.7 2D SVG Roof Rafter & Birdsmouth Drafting Console
Line Len 18' 7-15/16"
HAP 11-7/16"
IRC R802 PASS (9/12)
30' (360")
8' (Shed) 16' (1-Car) 24' (2-Car) 48' (Barn)
9/12 (36.9°)
3/12 (Low) 6/12 (Ranch) 9/12 (Steep) 12/12 (45°)
18" Horiz
✓ PASSES 2024 IRC R802.7.1 NOTCH LIMIT 36.9° Plumb

3-1/2" full plate bearing produces a 2-1/8" perpendicular notch (≤ 3-3/4" max D/3 limit for 2x12). HAP is 11-7/16".

2D IRC R802 Roof Rafter Span, Rise, Line Length & Birdsmouth HAP Blueprint Interactive scale CAD drawing of a gable roof framing cross-section showing exterior walls, ridge board deduction, common rafter line length, soffit tail, collar tie zone, and birdsmouth Height Above Plate. COLLAR TIE (UPPER 1/3) Rise: 11' 2-3/8" Net Run: 14' 11-1/8" Building Span: 30' 0" (360") + 18" Soffits PITCH: 9/12 (36.9°) | LINE: 18' 7-15/16" Total Cut w/ Tail: 20' 6-7/16" • HAP: 11-7/16"
Rafter Line Len
18' 7-15/16"
Run: 179-1/8"
Total Cut + Tail
20' 6-7/16"
Buy 22-ft 2x12
Height Above Plate
11-7/16"
Heel Cut: 2-5/8"
Plumb / Seat Angle
36.9° / 53.1°
Rise: 11' 2-3/8"
Total Rafters
62 pcs
31/side @ 16" OC

Hooked Tape-Measure Rafter Layout Schedule 15.00" / ft Run

Cut the ridge plumb angle at the top tip (0"), hook your tape on the long point of the crown edge, and pull down the board:

Cumulative Hooked Tape-Measure Marks Along Roof Rafter Top Edge
Layout Station Cumulative Mark Shop Saw / Square Spec
1. Ridge Plumb Cut (Peak) 0" (Hook Board Tip) 36.9° Miter Angle
2. Collar Tie Zone (Upper 1/3) 74-5/8" (74.64") IRC R802.4.6 Strap Limit
3. Birdsmouth Heel Plumb Line 223-15/16" (18' 7-15/16") HAP: 11-7/16"
4. Birdsmouth Level Seat Cut 3-1/2" Level Bearing 53.1° Seat • 2-5/8" Heel
5. Fascia Soffit Tail Plumb Cut 246-7/16" (20' 6-7/16") Tail: +22-1/2"

Required Bill of Materials (BOM) & Hardware

Auto-Calculated Quantities
  • 62 × 22-ft 2x12 #2 Kiln-Dried Framing Rafters 31 rafters per slope @ 16" OC across 40-ft ridge
  • 57 Sheets × 4x8 (7/16" or 5/8") APA Structural Roof Sheathing Covers 1643 sq ft sloped roof deck (+10% gable/starter waste)
  • 62 × Simpson Strong-Tie H2.5A Hurricane Rafter Ties Plus 11 × 1x6/2x4 Collar Ties (4ft OC) & 3 × 16-ft Ridge Boards

Independent Field Spec Notice: Geometry and birdsmouth notch limits follow 2024 IRC Sections R802.4, R802.6, and R802.7.1. Verify snow-load lumber spans against local R802.4.1 tables.

Need full-scale Jobsite Cut Sheet + Vector .SVG blueprint?

Pre-Calculated Roof Rafter Calculator Blueprints (12 Field Specs)

Select any standard jobsite specification below to load its exact 2D SVG diagram and engineering tables:

Open Base Roof Rafter Calculator →
Contractor & Instructor Widget

Embed This 2D SVG Instrument on Your Website (Ad-Free)

Carpentry instructors, trade schools, and builders can embed the standalone ad-free version of this 2D CAD calculator with one HTML snippet.

SPECIFICATION WALKTHROUGH // 30-Ft Barn (9/12 Pitch)

Mathematical Derivation & Field Specifications: 30-Ft Barn (9/12 Pitch)

Updated • Published by LayoutCalculator

For a 30-foot (360") building width framed at a 9/12 roof pitch (36.9° slope) with a 1.75" ridge board, subtracting half the ridge thickness per side leaves an adjusted horizontal run of 179-1/8" (179.13"). Multiplying by the unit secant factor 1.2500 establishes a ridge-to-heel line length of 18' 7-15/16" (223.91") and a ridge peak rise of 134.3" (11.20 ft) above the wall plate.

Adding a 18" horizontal eave projection contributes 22-1/2" of sloped tail stock, bringing overall cut length to 20' 6-7/16" (order 22-ft 2x12 boards). Per 2024 IRC Section R802.7.1, birdsmouth end notches on 2x12 (11.25" actual depth) must not exceed 3-3/4" (D/3), preserving a 11-7/16" Height Above Plate (HAP) across all 69 rafters (31 pairs @ 16" OC + 10% cull).

Roof Pitch Sensitivity Matrix for 30-Ft Building Span (18" Overhang)

Roof Pitch Plumb Cut Angle Secant Factor Main Line Length Total w/ Overhang Min Lumber Stock
4/12 18.4° 1.0541 15' 8-13/16" 17' 3-13/16" 18 ft 2x12
6/12 26.6° 1.1180 16' 8-1/4" 18' 4-3/8" 20 ft 2x12
8/12 33.7° 1.2019 17' 11-5/16" 19' 8-15/16" 20 ft 2x12
10/12 39.8° 1.3017 19' 5-3/16" 21' 4-5/8" 22 ft 2x12
12/12 45.0° 1.4142 21' 1-5/16" 23' 2-3/4" 24 ft 2x12

Pattern Rafter Scribe & Saw Layout Checkpoints (2x12 @ 9/12)

Checkpoint Hooked Tape / Angle Code / Framing Rule
1. Ridge Plumb Cut 0" Origin • 36.9° Miter Crown edge facing UP; deduct 0.875" half-ridge
2. Birdsmouth Heel Plumb 18' 7-15/16" (223.91") HAP = 11-7/16" above top plate; 3-1/2" level seat
3. Fascia Tail Plumb Cut 20' 6-7/16" (246.41") 18" horizontal soffit projection (36.9° plumb)

Official Building Code & Industry Standard Citations

Field Manuals & Code Tables for Roof Rafter Calculator

Index of All 107 Manuals →

Frequently Asked Questions (30-Ft Barn (9/12 Pitch))

What is the exact rafter line length and plumb cut angle for a 30-ft span at 9/12 pitch?

▼

Deducting half of a 1.75" ridge board from a 30-ft (360") building width leaves an adjusted horizontal run of 179-1/8". At 9/12 pitch (36.9° plumb cut, 53.1° seat cut), ridge-to-heel line length is 18' 7-15/16" (223.91") plus a 22-1/2" overhang tail (20' 6-7/16" overall).

What is the maximum birdsmouth notch depth allowed by IRC R802.7.1 on 2x12 rafters?

▼

Under 2024 IRC Section R802.7.1, an end-bearing birdsmouth notch cannot exceed one-third (D/3) of the actual rafter depth. For 2x12 lumber (11.25" actual depth), maximum notch depth is 3-3/4", preserving a 11-7/16" Height Above Plate (HAP).

What lumber length and quantity should I order for a 30' × 40' gable roof at 16" OC?

▼

Each 20' 6-7/16" common rafter requires 22-foot 2x12 stock. Across a 40-foot roof ridge at 16" on-center (31 rafter pairs), order 69 boards including a 10% culling buffer.