Skip to main content
LAYOUTCALCULATOR SCALE 1/16" CAD
2024 IRC Section R802 • SCALE: 1/16" FRACTIONAL
IRC R802 Birdsmouth Check Framing & Carpentry

26-Ft Gable (6/12 Pitch) — 26-Ft Gable Rafter Layout: 6/12 Pitch 2x10 Cuts

Pre-solved 26-ft gable roof rafter calculation at 6/12 pitch: 14 ft 5-9/16 in line length, 26.6° plumb cut, 18" overhang, and 18-ft 2x10 lumber order.

Calculation notes
Checked against: 2024 IRC Section R802
Published by LayoutCalculator. Confirm with your local building official.
REV DATE:
Result summary

Across a 155-1/4" adjusted run at 6/12 pitch (26.6°), line length reaches 14 ft 5-9/16 in plus a 20-1/8" overhang tail (16 ft 1-11/16 in total—order 62 × 18-ft 2x10s or trim overhang to 15" for 16-ft stock).

Typical Field Application

Deep 26x36 detached garages, ranch homes with wide 18-inch overhangs, and agricultural equipment sheds.

Field note

Notice how an 18" overhang pushes total length 1-11/16" past 16 feet—reducing horizontal overhang from 18" to 16" trims total length to 15 ft 11-11/16 in and saves buying 18-ft special-order stock.

IRC R802.4 & R802.7 2D SVG Roof Rafter & Birdsmouth Drafting Console
Line Len 14' 5-9/16"
HAP 8-9/16"
IRC R802 PASS (6/12)
26' (312")
8' (Shed) 16' (1-Car) 24' (2-Car) 48' (Barn)
6/12 (26.6°)
3/12 (Low) 6/12 (Ranch) 9/12 (Steep) 12/12 (45°)
18" Horiz
✓ PASSES 2024 IRC R802.7.1 NOTCH LIMIT 26.6° Plumb

3-1/2" full plate bearing produces a 1-9/16" perpendicular notch (≤ 3-1/16" max D/3 limit for 2x10). HAP is 8-9/16".

2D IRC R802 Roof Rafter Span, Rise, Line Length & Birdsmouth HAP Blueprint Interactive scale CAD drawing of a gable roof framing cross-section showing exterior walls, ridge board deduction, common rafter line length, soffit tail, collar tie zone, and birdsmouth Height Above Plate. COLLAR TIE (UPPER 1/3) Rise: 6' 5-5/8" Net Run: 12' 11-1/4" Building Span: 26' 0" (312") + 18" Soffits PITCH: 6/12 (26.6°) | LINE: 14' 5-9/16" Total Cut w/ Tail: 16' 1-11/16" • HAP: 8-9/16"
Rafter Line Len
14' 5-9/16"
Run: 155-1/4"
Total Cut + Tail
16' 1-11/16"
Buy 18-ft 2x10
Height Above Plate
8-9/16"
Heel Cut: 1-3/4"
Plumb / Seat Angle
26.6° / 63.4°
Rise: 6' 5-5/8"
Total Rafters
56 pcs
28/side @ 16" OC

Hooked Tape-Measure Rafter Layout Schedule 13.42" / ft Run

Cut the ridge plumb angle at the top tip (0"), hook your tape on the long point of the crown edge, and pull down the board:

Cumulative Hooked Tape-Measure Marks Along Roof Rafter Top Edge
Layout Station Cumulative Mark Shop Saw / Square Spec
1. Ridge Plumb Cut (Peak) 0" (Hook Board Tip) 26.6° Miter Angle
2. Collar Tie Zone (Upper 1/3) 57-7/8" (57.86") IRC R802.4.6 Strap Limit
3. Birdsmouth Heel Plumb Line 173-9/16" (14' 5-9/16") HAP: 8-9/16"
4. Birdsmouth Level Seat Cut 3-1/2" Level Bearing 63.4° Seat • 1-3/4" Heel
5. Fascia Soffit Tail Plumb Cut 193-11/16" (16' 1-11/16") Tail: +20-1/8"

Required Bill of Materials (BOM) & Hardware

Auto-Calculated Quantities
  • 56 × 18-ft 2x10 #2 Kiln-Dried Framing Rafters 28 rafters per slope @ 16" OC across 36-ft ridge
  • 40 Sheets × 4x8 (7/16" or 5/8") APA Structural Roof Sheathing Covers 1162 sq ft sloped roof deck (+10% gable/starter waste)
  • 56 × Simpson Strong-Tie H2.5A Hurricane Rafter Ties Plus 10 × 1x6/2x4 Collar Ties (4ft OC) & 3 × 16-ft Ridge Boards

Independent Field Spec Notice: Geometry and birdsmouth notch limits follow 2024 IRC Sections R802.4, R802.6, and R802.7.1. Verify snow-load lumber spans against local R802.4.1 tables.

Need full-scale Jobsite Cut Sheet + Vector .SVG blueprint?

Pre-Calculated Roof Rafter Calculator Blueprints (12 Field Specs)

Select any standard jobsite specification below to load its exact 2D SVG diagram and engineering tables:

Open Base Roof Rafter Calculator →
Contractor & Instructor Widget

Embed This 2D SVG Instrument on Your Website (Ad-Free)

Carpentry instructors, trade schools, and builders can embed the standalone ad-free version of this 2D CAD calculator with one HTML snippet.

SPECIFICATION WALKTHROUGH // 26-Ft Gable (6/12 Pitch)

Mathematical Derivation & Field Specifications: 26-Ft Gable (6/12 Pitch)

Updated • Published by LayoutCalculator

For a 26-foot (312") building width framed at a 6/12 roof pitch (26.6° slope) with a 1.5" ridge board, subtracting half the ridge thickness per side leaves an adjusted horizontal run of 155-1/4" (155.25"). Multiplying by the unit secant factor 1.1180 establishes a ridge-to-heel line length of 14' 5-9/16" (173.57") and a ridge peak rise of 77.6" (6.47 ft) above the wall plate.

Adding a 18" horizontal eave projection contributes 20-1/8" of sloped tail stock, bringing overall cut length to 16' 1-11/16" (order 18-ft 2x10 boards). Per 2024 IRC Section R802.7.1, birdsmouth end notches on 2x10 (9.25" actual depth) must not exceed 3-1/16" (D/3), preserving a 8-9/16" Height Above Plate (HAP) across all 62 rafters (28 pairs @ 16" OC + 10% cull).

Roof Pitch Sensitivity Matrix for 26-Ft Building Span (18" Overhang)

Roof Pitch Plumb Cut Angle Secant Factor Main Line Length Total w/ Overhang Min Lumber Stock
4/12 18.4° 1.0541 13' 7-5/8" 15' 2-5/8" 16 ft 2x10
6/12 (Selected) 26.6° 1.1180 14' 5-9/16" 16' 1-11/16" 18 ft 2x10
8/12 33.7° 1.2019 15' 6-9/16" 17' 4-1/4" 18 ft 2x10
10/12 39.8° 1.3017 16' 10-1/16" 18' 9-1/2" 20 ft 2x10
12/12 45.0° 1.4142 18' 3-9/16" 20' 5" 22 ft 2x10

Pattern Rafter Scribe & Saw Layout Checkpoints (2x10 @ 6/12)

Checkpoint Hooked Tape / Angle Code / Framing Rule
1. Ridge Plumb Cut 0" Origin • 26.6° Miter Crown edge facing UP; deduct 0.75" half-ridge
2. Birdsmouth Heel Plumb 14' 5-9/16" (173.57") HAP = 8-9/16" above top plate; 3-1/2" level seat
3. Fascia Tail Plumb Cut 16' 1-11/16" (193.70") 18" horizontal soffit projection (26.6° plumb)

Official Building Code & Industry Standard Citations

Field Manuals & Code Tables for Roof Rafter Calculator

Index of All 107 Manuals →

Frequently Asked Questions (26-Ft Gable (6/12 Pitch))

What is the exact rafter line length and plumb cut angle for a 26-ft span at 6/12 pitch?

▼

Deducting half of a 1.5" ridge board from a 26-ft (312") building width leaves an adjusted horizontal run of 155-1/4". At 6/12 pitch (26.6° plumb cut, 63.4° seat cut), ridge-to-heel line length is 14' 5-9/16" (173.57") plus a 20-1/8" overhang tail (16' 1-11/16" overall).

What is the maximum birdsmouth notch depth allowed by IRC R802.7.1 on 2x10 rafters?

▼

Under 2024 IRC Section R802.7.1, an end-bearing birdsmouth notch cannot exceed one-third (D/3) of the actual rafter depth. For 2x10 lumber (9.25" actual depth), maximum notch depth is 3-1/16", preserving a 8-9/16" Height Above Plate (HAP).

What lumber length and quantity should I order for a 26' × 36' gable roof at 16" OC?

▼

Each 16' 1-11/16" common rafter requires 18-foot 2x10 stock. Across a 36-foot roof ridge at 16" on-center (28 rafter pairs), order 62 boards including a 10% culling buffer.