Skip to main content
LAYOUTCALCULATOR SCALE 1/16" CAD
2024 IRC Section R802 • SCALE: 1/16" FRACTIONAL
IRC R802 Birdsmouth Check Framing & Carpentry

28-Ft Garage (8/12 Pitch) — 28-Ft Garage Rafter Layout: 8/12 Pitch 2x10 Cuts

Exact 28-ft two-car garage rafter framing diagram at 8/12 pitch: 16 ft 9 in line length, 33.7° plumb cut, 18" soffit tail, and 20-ft 2x10 stock count.

Calculation notes
Checked against: 2024 IRC Section R802
Published by LayoutCalculator. Confirm with your local building official.
REV DATE:
Result summary

At 8/12 pitch (33.7°), a 167-1/4" adjusted run requires a 201" (16 ft 9 in) main line length plus a 21-5/8" overhang tail, totaling 18 ft 6-5/8 in (order 20-foot #2 or better Douglas Fir 2x10s).

Typical Field Application

Oversized 28x28 garages with attic storage lofts, barn workshops, and high-snow-load northern gables.

Field note

On wide 28-foot spans without a structural ridge beam, install continuous ceiling joists nailed across the top plates plus upper-third 2x6 collar ties per IRC R802.4.6.

IRC R802.4 & R802.7 2D SVG Roof Rafter & Birdsmouth Drafting Console
Line Len 16' 9"
HAP 8-13/16"
IRC R802 PASS (8/12)
28' (336")
8' (Shed) 16' (1-Car) 24' (2-Car) 48' (Barn)
8/12 (33.7°)
3/12 (Low) 6/12 (Ranch) 9/12 (Steep) 12/12 (45°)
18" Horiz
✓ PASSES 2024 IRC R802.7.1 NOTCH LIMIT 33.7° Plumb

3-1/2" full plate bearing produces a 1-15/16" perpendicular notch (≤ 3-1/16" max D/3 limit for 2x10). HAP is 8-13/16".

2D IRC R802 Roof Rafter Span, Rise, Line Length & Birdsmouth HAP Blueprint Interactive scale CAD drawing of a gable roof framing cross-section showing exterior walls, ridge board deduction, common rafter line length, soffit tail, collar tie zone, and birdsmouth Height Above Plate. COLLAR TIE (UPPER 1/3) Rise: 9' 3-1/2" Net Run: 13' 11-1/4" Building Span: 28' 0" (336") + 18" Soffits PITCH: 8/12 (33.7°) | LINE: 16' 9" Total Cut w/ Tail: 18' 6-5/8" • HAP: 8-13/16"
Rafter Line Len
16' 9"
Run: 167-1/4"
Total Cut + Tail
18' 6-5/8"
Buy 20-ft 2x10
Height Above Plate
8-13/16"
Heel Cut: 2-5/16"
Plumb / Seat Angle
33.7° / 56.3°
Rise: 9' 3-1/2"
Total Rafters
44 pcs
22/side @ 16" OC

Hooked Tape-Measure Rafter Layout Schedule 14.42" / ft Run

Cut the ridge plumb angle at the top tip (0"), hook your tape on the long point of the crown edge, and pull down the board:

Cumulative Hooked Tape-Measure Marks Along Roof Rafter Top Edge
Layout Station Cumulative Mark Shop Saw / Square Spec
1. Ridge Plumb Cut (Peak) 0" (Hook Board Tip) 33.7° Miter Angle
2. Collar Tie Zone (Upper 1/3) 67" (67.00") IRC R802.4.6 Strap Limit
3. Birdsmouth Heel Plumb Line 201" (16' 9") HAP: 8-13/16"
4. Birdsmouth Level Seat Cut 3-1/2" Level Bearing 56.3° Seat • 2-5/16" Heel
5. Fascia Soffit Tail Plumb Cut 222-5/8" (18' 6-5/8") Tail: +21-5/8"

Required Bill of Materials (BOM) & Hardware

Auto-Calculated Quantities
  • 44 × 20-ft 2x10 #2 Kiln-Dried Framing Rafters 22 rafters per slope @ 16" OC across 28-ft ridge
  • 36 Sheets × 4x8 (7/16" or 5/8") APA Structural Roof Sheathing Covers 1039 sq ft sloped roof deck (+10% gable/starter waste)
  • 44 × Simpson Strong-Tie H2.5A Hurricane Rafter Ties Plus 8 × 1x6/2x4 Collar Ties (4ft OC) & 2 × 16-ft Ridge Boards

Independent Field Spec Notice: Geometry and birdsmouth notch limits follow 2024 IRC Sections R802.4, R802.6, and R802.7.1. Verify snow-load lumber spans against local R802.4.1 tables.

Need full-scale Jobsite Cut Sheet + Vector .SVG blueprint?

Pre-Calculated Roof Rafter Calculator Blueprints (12 Field Specs)

Select any standard jobsite specification below to load its exact 2D SVG diagram and engineering tables:

Open Base Roof Rafter Calculator →
Contractor & Instructor Widget

Embed This 2D SVG Instrument on Your Website (Ad-Free)

Carpentry instructors, trade schools, and builders can embed the standalone ad-free version of this 2D CAD calculator with one HTML snippet.

SPECIFICATION WALKTHROUGH // 28-Ft Garage (8/12 Pitch)

Mathematical Derivation & Field Specifications: 28-Ft Garage (8/12 Pitch)

Updated • Published by LayoutCalculator

For a 28-foot (336") building width framed at a 8/12 roof pitch (33.7° slope) with a 1.5" ridge board, subtracting half the ridge thickness per side leaves an adjusted horizontal run of 167-1/4" (167.25"). Multiplying by the unit secant factor 1.2019 establishes a ridge-to-heel line length of 16' 9" (201.01") and a ridge peak rise of 111.5" (9.29 ft) above the wall plate.

Adding a 18" horizontal eave projection contributes 21-5/8" of sloped tail stock, bringing overall cut length to 18' 6-5/8" (order 20-ft 2x10 boards). Per 2024 IRC Section R802.7.1, birdsmouth end notches on 2x10 (9.25" actual depth) must not exceed 3-1/16" (D/3), preserving a 8-13/16" Height Above Plate (HAP) across all 49 rafters (22 pairs @ 16" OC + 10% cull).

Roof Pitch Sensitivity Matrix for 28-Ft Building Span (18" Overhang)

Roof Pitch Plumb Cut Angle Secant Factor Main Line Length Total w/ Overhang Min Lumber Stock
4/12 18.4° 1.0541 14' 8-5/16" 16' 3-1/4" 18 ft 2x10
6/12 26.6° 1.1180 15' 7" 17' 3-1/8" 18 ft 2x10
8/12 (Selected) 33.7° 1.2019 16' 9" 18' 6-5/8" 20 ft 2x10
10/12 39.8° 1.3017 18' 1-11/16" 20' 1-1/8" 22 ft 2x10
12/12 45.0° 1.4142 19' 8-1/2" 21' 10" 22 ft 2x10

Pattern Rafter Scribe & Saw Layout Checkpoints (2x10 @ 8/12)

Checkpoint Hooked Tape / Angle Code / Framing Rule
1. Ridge Plumb Cut 0" Origin • 33.7° Miter Crown edge facing UP; deduct 0.75" half-ridge
2. Birdsmouth Heel Plumb 16' 9" (201.01") HAP = 8-13/16" above top plate; 3-1/2" level seat
3. Fascia Tail Plumb Cut 18' 6-5/8" (222.64") 18" horizontal soffit projection (33.7° plumb)

Official Building Code & Industry Standard Citations

Field Manuals & Code Tables for Roof Rafter Calculator

Index of All 107 Manuals →

Frequently Asked Questions (28-Ft Garage (8/12 Pitch))

What is the exact rafter line length and plumb cut angle for a 28-ft span at 8/12 pitch?

▼

Deducting half of a 1.5" ridge board from a 28-ft (336") building width leaves an adjusted horizontal run of 167-1/4". At 8/12 pitch (33.7° plumb cut, 56.3° seat cut), ridge-to-heel line length is 16' 9" (201.01") plus a 21-5/8" overhang tail (18' 6-5/8" overall).

What is the maximum birdsmouth notch depth allowed by IRC R802.7.1 on 2x10 rafters?

▼

Under 2024 IRC Section R802.7.1, an end-bearing birdsmouth notch cannot exceed one-third (D/3) of the actual rafter depth. For 2x10 lumber (9.25" actual depth), maximum notch depth is 3-1/16", preserving a 8-13/16" Height Above Plate (HAP).

What lumber length and quantity should I order for a 28' × 28' gable roof at 16" OC?

▼

Each 18' 6-5/8" common rafter requires 20-foot 2x10 stock. Across a 28-foot roof ridge at 16" on-center (22 rafter pairs), order 49 boards including a 10% culling buffer.