Skip to main content
LAYOUTCALCULATOR SCALE 1/16" CAD
2024 IRC Section R802 • SCALE: 1/16" FRACTIONAL
IRC R802 Birdsmouth Check Framing & Carpentry

20-Ft Cabin (12/12 Pitch) — 20-Ft Cabin Roof Rafters: 12/12 Pitch (45°) Layout

Steep 12/12 pitch (45-degree) cabin rafter CAD layout for a 20-ft span: 14 ft 5/8 in line length, symmetric 45° plumb/seat cuts, and 16-ft 2x10 sizing.

Calculation notes
Checked against: 2024 IRC Section R802
Published by LayoutCalculator. Confirm with your local building official.
REV DATE:
Result summary

12/12 pitch produces an exact 45.0° plumb and seat cut angle (unit factor 1.4142). Total rafter length with a 16" horizontal eave is 191-1/4" (15 ft 11-1/4 in), maximizing a 16-ft 2x10.

Typical Field Application

Mountain loft cabins, steep snow-shedding Alpine gables, and cathedral vaulted timber-framed ceilings.

Field note

Because 191-1/4" leaves only 3/4" of spare wood on a nominal 16-foot (192") board, measure actual mill length (~192-1/2") at the lumberyard and select boards free of end splits.

IRC R802.4 & R802.7 2D SVG Roof Rafter & Birdsmouth Drafting Console
Line Len 14' 5/8"
HAP 9-9/16"
IRC R802 PASS (12/12)
20' (240")
8' (Shed) 16' (1-Car) 24' (2-Car) 48' (Barn)
12/12 (45.0°)
3/12 (Low) 6/12 (Ranch) 9/12 (Steep) 12/12 (45°)
16" Horiz
✓ PASSES 2024 IRC R802.7.1 NOTCH LIMIT 45.0° Plumb

3-1/2" full plate bearing produces a 2-1/2" perpendicular notch (≤ 3-1/16" max D/3 limit for 2x10). HAP is 9-9/16".

2D IRC R802 Roof Rafter Span, Rise, Line Length & Birdsmouth HAP Blueprint Interactive scale CAD drawing of a gable roof framing cross-section showing exterior walls, ridge board deduction, common rafter line length, soffit tail, collar tie zone, and birdsmouth Height Above Plate. COLLAR TIE (UPPER 1/3) Rise: 9' 11-1/4" Net Run: 9' 11-1/4" Building Span: 20' 0" (240") + 16" Soffits PITCH: 12/12 (45.0°) | LINE: 14' 5/8" Total Cut w/ Tail: 15' 11-1/4" • HAP: 9-9/16"
Rafter Line Len
14' 5/8"
Run: 119-1/4"
Total Cut + Tail
15' 11-1/4"
Buy 16-ft 2x10
Height Above Plate
9-9/16"
Heel Cut: 3-1/2"
Plumb / Seat Angle
45.0° / 45.0°
Rise: 9' 11-1/4"
Total Rafters
38 pcs
19/side @ 16" OC

Hooked Tape-Measure Rafter Layout Schedule 16.97" / ft Run

Cut the ridge plumb angle at the top tip (0"), hook your tape on the long point of the crown edge, and pull down the board:

Cumulative Hooked Tape-Measure Marks Along Roof Rafter Top Edge
Layout Station Cumulative Mark Shop Saw / Square Spec
1. Ridge Plumb Cut (Peak) 0" (Hook Board Tip) 45.0° Miter Angle
2. Collar Tie Zone (Upper 1/3) 56-3/16" (56.21") IRC R802.4.6 Strap Limit
3. Birdsmouth Heel Plumb Line 168-5/8" (14' 5/8") HAP: 9-9/16"
4. Birdsmouth Level Seat Cut 3-1/2" Level Bearing 45.0° Seat • 3-1/2" Heel
5. Fascia Soffit Tail Plumb Cut 191-1/4" (15' 11-1/4") Tail: +22-5/8"

Required Bill of Materials (BOM) & Hardware

Auto-Calculated Quantities
  • 38 × 16-ft 2x10 #2 Kiln-Dried Framing Rafters 19 rafters per slope @ 16" OC across 24-ft ridge
  • 27 Sheets × 4x8 (7/16" or 5/8") APA Structural Roof Sheathing Covers 765 sq ft sloped roof deck (+10% gable/starter waste)
  • 38 × Simpson Strong-Tie H2.5A Hurricane Rafter Ties Plus 7 × 1x6/2x4 Collar Ties (4ft OC) & 2 × 16-ft Ridge Boards

Independent Field Spec Notice: Geometry and birdsmouth notch limits follow 2024 IRC Sections R802.4, R802.6, and R802.7.1. Verify snow-load lumber spans against local R802.4.1 tables.

Need full-scale Jobsite Cut Sheet + Vector .SVG blueprint?

Pre-Calculated Roof Rafter Calculator Blueprints (12 Field Specs)

Select any standard jobsite specification below to load its exact 2D SVG diagram and engineering tables:

Open Base Roof Rafter Calculator →
Contractor & Instructor Widget

Embed This 2D SVG Instrument on Your Website (Ad-Free)

Carpentry instructors, trade schools, and builders can embed the standalone ad-free version of this 2D CAD calculator with one HTML snippet.

SPECIFICATION WALKTHROUGH // 20-Ft Cabin (12/12 Pitch)

Mathematical Derivation & Field Specifications: 20-Ft Cabin (12/12 Pitch)

Updated • Published by LayoutCalculator

For a 20-foot (240") building width framed at a 12/12 roof pitch (45.0° slope) with a 1.5" ridge board, subtracting half the ridge thickness per side leaves an adjusted horizontal run of 119-1/4" (119.25"). Multiplying by the unit secant factor 1.4142 establishes a ridge-to-heel line length of 14' 5/8" (168.64") and a ridge peak rise of 119.3" (9.94 ft) above the wall plate.

Adding a 16" horizontal eave projection contributes 22-5/8" of sloped tail stock, bringing overall cut length to 15' 11-1/4" (order 16-ft 2x10 boards). Per 2024 IRC Section R802.7.1, birdsmouth end notches on 2x10 (9.25" actual depth) must not exceed 3-1/16" (D/3), preserving a 10" Height Above Plate (HAP) across all 42 rafters (19 pairs @ 16" OC + 10% cull).

Roof Pitch Sensitivity Matrix for 20-Ft Building Span (16" Overhang)

Roof Pitch Plumb Cut Angle Secant Factor Main Line Length Total w/ Overhang Min Lumber Stock
4/12 18.4° 1.0541 10' 5-11/16" 11' 10-9/16" 12 ft 2x10
6/12 26.6° 1.1180 11' 1-5/16" 12' 7-3/16" 14 ft 2x10
8/12 33.7° 1.2019 11' 11-5/16" 13' 6-9/16" 14 ft 2x10
10/12 39.8° 1.3017 12' 11-1/4" 14' 8-1/16" 16 ft 2x10
12/12 (Selected) 45.0° 1.4142 14' 5/8" 15' 11-1/4" 16 ft 2x10

Pattern Rafter Scribe & Saw Layout Checkpoints (2x10 @ 12/12)

Checkpoint Hooked Tape / Angle Code / Framing Rule
1. Ridge Plumb Cut 0" Origin • 45.0° Miter Crown edge facing UP; deduct 0.75" half-ridge
2. Birdsmouth Heel Plumb 14' 5/8" (168.64") HAP = 10" above top plate; 3-1/16" level seat
3. Fascia Tail Plumb Cut 15' 11-1/4" (191.27") 16" horizontal soffit projection (45.0° plumb)

Official Building Code & Industry Standard Citations

Field Manuals & Code Tables for Roof Rafter Calculator

Index of All 107 Manuals →

Frequently Asked Questions (20-Ft Cabin (12/12 Pitch))

What is the exact rafter line length and plumb cut angle for a 20-ft span at 12/12 pitch?

▼

Deducting half of a 1.5" ridge board from a 20-ft (240") building width leaves an adjusted horizontal run of 119-1/4". At 12/12 pitch (45.0° plumb cut, 45.0° seat cut), ridge-to-heel line length is 14' 5/8" (168.64") plus a 22-5/8" overhang tail (15' 11-1/4" overall).

What is the maximum birdsmouth notch depth allowed by IRC R802.7.1 on 2x10 rafters?

▼

Under 2024 IRC Section R802.7.1, an end-bearing birdsmouth notch cannot exceed one-third (D/3) of the actual rafter depth. For 2x10 lumber (9.25" actual depth), maximum notch depth is 3-1/16", preserving a 10" Height Above Plate (HAP).

What lumber length and quantity should I order for a 20' × 24' gable roof at 16" OC?

▼

Each 15' 11-1/4" common rafter requires 16-foot 2x10 stock. Across a 24-foot roof ridge at 16" on-center (19 rafter pairs), order 42 boards including a 10% culling buffer.