Skip to main content
LAYOUTCALCULATOR SCALE 1/16" CAD
2024 IRC Section R802 • SCALE: 1/16" FRACTIONAL
IRC R802 Birdsmouth Check Framing & Carpentry

22-Ft House (7/12 Pitch) — 22-Ft House Rafter Layout: 7/12 Pitch 2x10 Framing

Residential 22-ft gable roof rafter blueprint at 7/12 pitch: 12 ft 7-15/16 in line length, 30.3° plumb cut, 16" eave tail, and 16-ft 2x10 lumber list.

Calculation notes
Checked against: 2024 IRC Section R802
Published by LayoutCalculator. Confirm with your local building official.
REV DATE:
Result summary

At 7/12 pitch (30.3°), a 131-1/4" adjusted run requires 12 ft 7-15/16 in of main rafter line plus an 18-1/2" tail (14 ft 2-1/2 in overall—order 53 × 16-ft 2x10 boards for a 30-ft roof).

Typical Field Application

Custom cottages, Craftsman bungalows, two-story home wings, and walk-able residential shingle roofs.

Field note

Save the clean 21-inch 2x10 offcuts from your 16-foot stock to rip matching sub-fascia blocks and solid eave bird-blocking between rafters.

IRC R802.4 & R802.7 2D SVG Roof Rafter & Birdsmouth Drafting Console
Line Len 12' 7-15/16"
HAP 8-11/16"
IRC R802 PASS (7/12)
22' (264")
8' (Shed) 16' (1-Car) 24' (2-Car) 48' (Barn)
7/12 (30.3°)
3/12 (Low) 6/12 (Ranch) 9/12 (Steep) 12/12 (45°)
16" Horiz
✓ PASSES 2024 IRC R802.7.1 NOTCH LIMIT 30.3° Plumb

3-1/2" full plate bearing produces a 1-3/4" perpendicular notch (≤ 3-1/16" max D/3 limit for 2x10). HAP is 8-11/16".

2D IRC R802 Roof Rafter Span, Rise, Line Length & Birdsmouth HAP Blueprint Interactive scale CAD drawing of a gable roof framing cross-section showing exterior walls, ridge board deduction, common rafter line length, soffit tail, collar tie zone, and birdsmouth Height Above Plate. COLLAR TIE (UPPER 1/3) Rise: 6' 4-9/16" Net Run: 10' 11-1/4" Building Span: 22' 0" (264") + 16" Soffits PITCH: 7/12 (30.3°) | LINE: 12' 7-15/16" Total Cut w/ Tail: 14' 2-1/2" • HAP: 8-11/16"
Rafter Line Len
12' 7-15/16"
Run: 131-1/4"
Total Cut + Tail
14' 2-1/2"
Buy 16-ft 2x10
Height Above Plate
8-11/16"
Heel Cut: 2-1/16"
Plumb / Seat Angle
30.3° / 59.7°
Rise: 6' 4-9/16"
Total Rafters
48 pcs
24/side @ 16" OC

Hooked Tape-Measure Rafter Layout Schedule 13.89" / ft Run

Cut the ridge plumb angle at the top tip (0"), hook your tape on the long point of the crown edge, and pull down the board:

Cumulative Hooked Tape-Measure Marks Along Roof Rafter Top Edge
Layout Station Cumulative Mark Shop Saw / Square Spec
1. Ridge Plumb Cut (Peak) 0" (Hook Board Tip) 30.3° Miter Angle
2. Collar Tie Zone (Upper 1/3) 50-5/8" (50.65") IRC R802.4.6 Strap Limit
3. Birdsmouth Heel Plumb Line 151-15/16" (12' 7-15/16") HAP: 8-11/16"
4. Birdsmouth Level Seat Cut 3-1/2" Level Bearing 59.7° Seat • 2-1/16" Heel
5. Fascia Soffit Tail Plumb Cut 170-1/2" (14' 2-1/2") Tail: +18-1/2"

Required Bill of Materials (BOM) & Hardware

Auto-Calculated Quantities
  • 48 × 16-ft 2x10 #2 Kiln-Dried Framing Rafters 24 rafters per slope @ 16" OC across 30-ft ridge
  • 30 Sheets × 4x8 (7/16" or 5/8") APA Structural Roof Sheathing Covers 852 sq ft sloped roof deck (+10% gable/starter waste)
  • 48 × Simpson Strong-Tie H2.5A Hurricane Rafter Ties Plus 8 × 1x6/2x4 Collar Ties (4ft OC) & 2 × 16-ft Ridge Boards

Independent Field Spec Notice: Geometry and birdsmouth notch limits follow 2024 IRC Sections R802.4, R802.6, and R802.7.1. Verify snow-load lumber spans against local R802.4.1 tables.

Need full-scale Jobsite Cut Sheet + Vector .SVG blueprint?

Pre-Calculated Roof Rafter Calculator Blueprints (12 Field Specs)

Select any standard jobsite specification below to load its exact 2D SVG diagram and engineering tables:

Open Base Roof Rafter Calculator →
Contractor & Instructor Widget

Embed This 2D SVG Instrument on Your Website (Ad-Free)

Carpentry instructors, trade schools, and builders can embed the standalone ad-free version of this 2D CAD calculator with one HTML snippet.

SPECIFICATION WALKTHROUGH // 22-Ft House (7/12 Pitch)

Mathematical Derivation & Field Specifications: 22-Ft House (7/12 Pitch)

Updated • Published by LayoutCalculator

For a 22-foot (264") building width framed at a 7/12 roof pitch (30.3° slope) with a 1.5" ridge board, subtracting half the ridge thickness per side leaves an adjusted horizontal run of 131-1/4" (131.25"). Multiplying by the unit secant factor 1.1577 establishes a ridge-to-heel line length of 12' 7-15/16" (151.95") and a ridge peak rise of 76.6" (6.38 ft) above the wall plate.

Adding a 16" horizontal eave projection contributes 18-1/2" of sloped tail stock, bringing overall cut length to 14' 2-1/2" (order 16-ft 2x10 boards). Per 2024 IRC Section R802.7.1, birdsmouth end notches on 2x10 (9.25" actual depth) must not exceed 3-1/16" (D/3), preserving a 8-11/16" Height Above Plate (HAP) across all 53 rafters (24 pairs @ 16" OC + 10% cull).

Roof Pitch Sensitivity Matrix for 22-Ft Building Span (16" Overhang)

Roof Pitch Plumb Cut Angle Secant Factor Main Line Length Total w/ Overhang Min Lumber Stock
4/12 18.4° 1.0541 11' 6-3/8" 12' 11-3/16" 14 ft 2x10
6/12 26.6° 1.1180 12' 2-3/4" 13' 8-5/8" 14 ft 2x10
8/12 33.7° 1.2019 13' 1-3/4" 14' 9" 16 ft 2x10
10/12 39.8° 1.3017 14' 2-7/8" 15' 11-11/16" 16 ft 2x10
12/12 45.0° 1.4142 15' 5-5/8" 17' 4-1/4" 18 ft 2x10

Pattern Rafter Scribe & Saw Layout Checkpoints (2x10 @ 7/12)

Checkpoint Hooked Tape / Angle Code / Framing Rule
1. Ridge Plumb Cut 0" Origin • 30.3° Miter Crown edge facing UP; deduct 0.75" half-ridge
2. Birdsmouth Heel Plumb 12' 7-15/16" (151.95") HAP = 8-11/16" above top plate; 3-1/2" level seat
3. Fascia Tail Plumb Cut 14' 2-1/2" (170.47") 16" horizontal soffit projection (30.3° plumb)

Official Building Code & Industry Standard Citations

Field Manuals & Code Tables for Roof Rafter Calculator

Index of All 107 Manuals →

Frequently Asked Questions (22-Ft House (7/12 Pitch))

What is the exact rafter line length and plumb cut angle for a 22-ft span at 7/12 pitch?

▼

Deducting half of a 1.5" ridge board from a 22-ft (264") building width leaves an adjusted horizontal run of 131-1/4". At 7/12 pitch (30.3° plumb cut, 59.7° seat cut), ridge-to-heel line length is 12' 7-15/16" (151.95") plus a 18-1/2" overhang tail (14' 2-1/2" overall).

What is the maximum birdsmouth notch depth allowed by IRC R802.7.1 on 2x10 rafters?

▼

Under 2024 IRC Section R802.7.1, an end-bearing birdsmouth notch cannot exceed one-third (D/3) of the actual rafter depth. For 2x10 lumber (9.25" actual depth), maximum notch depth is 3-1/16", preserving a 8-11/16" Height Above Plate (HAP).

What lumber length and quantity should I order for a 22' × 30' gable roof at 16" OC?

▼

Each 14' 2-1/2" common rafter requires 16-foot 2x10 stock. Across a 30-foot roof ridge at 16" on-center (24 rafter pairs), order 53 boards including a 10% culling buffer.