Skip to main content
LAYOUTCALCULATOR SCALE 1/16" CAD
2024 IRC Section R802 • SCALE: 1/16" FRACTIONAL
IRC R802 Birdsmouth Check Framing & Carpentry

32-Ft Custom (10/12 Pitch) — 32-Ft Steep Gable Rafters: 10/12 Pitch 2x12 Layout

Full-span 32-ft custom home rafter layout at 10/12 pitch on a 1-3/4" LVL ridge: 20 ft 8-13/16 in line length, 39.8° plumb angle, and 24-ft 2x12 stock.

Calculation notes
Checked against: 2024 IRC Section R802
Published by LayoutCalculator. Confirm with your local building official.
REV DATE:
Result summary

With a 191-1/8" adjusted half-span at 10/12 pitch (39.8°), ridge-to-plate line length is 20 ft 8-13/16 in plus a 23-7/16" soffit tail (22 ft 8-1/4 in overall—specify 24-ft engineered I-joists or #1 2x12s).

Typical Field Application

Large custom Tudor/French Country residences, cathedral ceilings, and full walk-up attic gables.

Field note

At 22 ft 8-1/4 in overall length, verify unbraced 2x12 span limits against IRC Table R802.4.1 for your local ground snow load, or add mid-span purlin kneewalls.

IRC R802.4 & R802.7 2D SVG Roof Rafter & Birdsmouth Drafting Console
Line Len 20' 8-13/16"
HAP 11-3/4"
IRC R802 PASS (10/12)
32' (384")
8' (Shed) 16' (1-Car) 24' (2-Car) 48' (Barn)
10/12 (39.8°)
3/12 (Low) 6/12 (Ranch) 9/12 (Steep) 12/12 (45°)
18" Horiz
✓ PASSES 2024 IRC R802.7.1 NOTCH LIMIT 39.8° Plumb

3-1/2" full plate bearing produces a 2-1/4" perpendicular notch (≤ 3-3/4" max D/3 limit for 2x12). HAP is 11-3/4".

2D IRC R802 Roof Rafter Span, Rise, Line Length & Birdsmouth HAP Blueprint Interactive scale CAD drawing of a gable roof framing cross-section showing exterior walls, ridge board deduction, common rafter line length, soffit tail, collar tie zone, and birdsmouth Height Above Plate. COLLAR TIE (UPPER 1/3) Rise: 13' 3-1/4" Net Run: 15' 11-1/8" Building Span: 32' 0" (384") + 18" Soffits PITCH: 10/12 (39.8°) | LINE: 20' 8-13/16" Total Cut w/ Tail: 22' 8-1/4" • HAP: 11-3/4"
Rafter Line Len
20' 8-13/16"
Run: 191-1/8"
Total Cut + Tail
22' 8-1/4"
Buy 24-ft 2x12
Height Above Plate
11-3/4"
Heel Cut: 2-15/16"
Plumb / Seat Angle
39.8° / 50.2°
Rise: 13' 3-1/4"
Total Rafters
68 pcs
34/side @ 16" OC

Hooked Tape-Measure Rafter Layout Schedule 15.62" / ft Run

Cut the ridge plumb angle at the top tip (0"), hook your tape on the long point of the crown edge, and pull down the board:

Cumulative Hooked Tape-Measure Marks Along Roof Rafter Top Edge
Layout Station Cumulative Mark Shop Saw / Square Spec
1. Ridge Plumb Cut (Peak) 0" (Hook Board Tip) 39.8° Miter Angle
2. Collar Tie Zone (Upper 1/3) 82-15/16" (82.93") IRC R802.4.6 Strap Limit
3. Birdsmouth Heel Plumb Line 248-13/16" (20' 8-13/16") HAP: 11-3/4"
4. Birdsmouth Level Seat Cut 3-1/2" Level Bearing 50.2° Seat • 2-15/16" Heel
5. Fascia Soffit Tail Plumb Cut 272-1/4" (22' 8-1/4") Tail: +23-7/16"

Required Bill of Materials (BOM) & Hardware

Auto-Calculated Quantities
  • 68 × 24-ft 2x12 #2 Kiln-Dried Framing Rafters 34 rafters per slope @ 16" OC across 44-ft ridge
  • 69 Sheets × 4x8 (7/16" or 5/8") APA Structural Roof Sheathing Covers 1996 sq ft sloped roof deck (+10% gable/starter waste)
  • 68 × Simpson Strong-Tie H2.5A Hurricane Rafter Ties Plus 12 × 1x6/2x4 Collar Ties (4ft OC) & 3 × 16-ft Ridge Boards

Independent Field Spec Notice: Geometry and birdsmouth notch limits follow 2024 IRC Sections R802.4, R802.6, and R802.7.1. Verify snow-load lumber spans against local R802.4.1 tables.

Need full-scale Jobsite Cut Sheet + Vector .SVG blueprint?

Pre-Calculated Roof Rafter Calculator Blueprints (12 Field Specs)

Select any standard jobsite specification below to load its exact 2D SVG diagram and engineering tables:

Open Base Roof Rafter Calculator →
Contractor & Instructor Widget

Embed This 2D SVG Instrument on Your Website (Ad-Free)

Carpentry instructors, trade schools, and builders can embed the standalone ad-free version of this 2D CAD calculator with one HTML snippet.

SPECIFICATION WALKTHROUGH // 32-Ft Custom (10/12 Pitch)

Mathematical Derivation & Field Specifications: 32-Ft Custom (10/12 Pitch)

Updated • Published by LayoutCalculator

For a 32-foot (384") building width framed at a 10/12 roof pitch (39.8° slope) with a 1.75" ridge board, subtracting half the ridge thickness per side leaves an adjusted horizontal run of 191-1/8" (191.13"). Multiplying by the unit secant factor 1.3017 establishes a ridge-to-heel line length of 20' 8-13/16" (248.79") and a ridge peak rise of 159.3" (13.27 ft) above the wall plate.

Adding a 18" horizontal eave projection contributes 23-7/16" of sloped tail stock, bringing overall cut length to 22' 8-1/4" (order 24-ft 2x12 boards). Per 2024 IRC Section R802.7.1, birdsmouth end notches on 2x12 (11.25" actual depth) must not exceed 3-3/4" (D/3), preserving a 11-3/4" Height Above Plate (HAP) across all 75 rafters (34 pairs @ 16" OC + 10% cull).

Roof Pitch Sensitivity Matrix for 32-Ft Building Span (18" Overhang)

Roof Pitch Plumb Cut Angle Secant Factor Main Line Length Total w/ Overhang Min Lumber Stock
4/12 18.4° 1.0541 16' 9-7/16" 18' 4-7/16" 20 ft 2x12
6/12 26.6° 1.1180 17' 9-11/16" 19' 5-13/16" 20 ft 2x12
8/12 33.7° 1.2019 19' 1-11/16" 20' 11-5/16" 22 ft 2x12
10/12 (Selected) 39.8° 1.3017 20' 8-13/16" 22' 8-1/4" 24 ft 2x12
12/12 45.0° 1.4142 22' 6-5/16" 24' 7-3/4" 26 ft 2x12

Pattern Rafter Scribe & Saw Layout Checkpoints (2x12 @ 10/12)

Checkpoint Hooked Tape / Angle Code / Framing Rule
1. Ridge Plumb Cut 0" Origin • 39.8° Miter Crown edge facing UP; deduct 0.875" half-ridge
2. Birdsmouth Heel Plumb 20' 8-13/16" (248.79") HAP = 11-3/4" above top plate; 3-1/2" level seat
3. Fascia Tail Plumb Cut 22' 8-1/4" (272.22") 18" horizontal soffit projection (39.8° plumb)

Official Building Code & Industry Standard Citations

Field Manuals & Code Tables for Roof Rafter Calculator

Index of All 107 Manuals →

Frequently Asked Questions (32-Ft Custom (10/12 Pitch))

What is the exact rafter line length and plumb cut angle for a 32-ft span at 10/12 pitch?

▼

Deducting half of a 1.75" ridge board from a 32-ft (384") building width leaves an adjusted horizontal run of 191-1/8". At 10/12 pitch (39.8° plumb cut, 50.2° seat cut), ridge-to-heel line length is 20' 8-13/16" (248.79") plus a 23-7/16" overhang tail (22' 8-1/4" overall).

What is the maximum birdsmouth notch depth allowed by IRC R802.7.1 on 2x12 rafters?

▼

Under 2024 IRC Section R802.7.1, an end-bearing birdsmouth notch cannot exceed one-third (D/3) of the actual rafter depth. For 2x12 lumber (11.25" actual depth), maximum notch depth is 3-3/4", preserving a 11-3/4" Height Above Plate (HAP).

What lumber length and quantity should I order for a 32' × 44' gable roof at 16" OC?

▼

Each 22' 8-1/4" common rafter requires 24-foot 2x12 stock. Across a 44-foot roof ridge at 16" on-center (34 rafter pairs), order 75 boards including a 10% culling buffer.