Skip to main content
LAYOUTCALCULATOR SCALE 1/16" CAD
2024 IRC Section R802 • SCALE: 1/16" FRACTIONAL
IRC R802 Birdsmouth Check Framing & Carpentry

16-Ft Shed (5/12 Pitch) — 16-Ft Shed Rafter Layout: 5/12 Pitch 2x8 Cut List

2D CAD rafter framing blueprint for a 16-ft workshop shed at 5/12 pitch: 8 ft 7-3/16 in line length, 22.6° plumb cut, 12" overhang, and 10-ft 2x8s.

Calculation notes
Checked against: 2024 IRC Section R802
Published by LayoutCalculator. Confirm with your local building official.
REV DATE:
Result summary

With a 95-1/4" adjusted run at 5/12 pitch (22.6°), main rafter line length is 8 ft 7-3/16 in plus an exact 13" overhang hypotenuse (9 ft 8-3/16 in total—order 36 × 10-ft 2x8s for a 20-ft ridge).

Typical Field Application

16x20 single-car garages, tractor storage barns, hobby woodshops, and backyard guest studios.

Field note

5/12 forms a classic 5-12-13 Pythagorean right triangle—every 12 inches of horizontal overhang adds an exact 13-inch sloped tail with zero fractional rounding error.

IRC R802.4 & R802.7 2D SVG Roof Rafter & Birdsmouth Drafting Console
Line Len 8' 7-3/16"
HAP 6-3/8"
IRC R802 PASS (5/12)
16' (192")
8' (Shed) 16' (1-Car) 24' (2-Car) 48' (Barn)
5/12 (22.6°)
3/12 (Low) 6/12 (Ranch) 9/12 (Steep) 12/12 (45°)
12" Horiz
✓ PASSES 2024 IRC R802.7.1 NOTCH LIMIT 22.6° Plumb

3-1/2" full plate bearing produces a 1-3/8" perpendicular notch (≤ 2-7/16" max D/3 limit for 2x8). HAP is 6-3/8".

2D IRC R802 Roof Rafter Span, Rise, Line Length & Birdsmouth HAP Blueprint Interactive scale CAD drawing of a gable roof framing cross-section showing exterior walls, ridge board deduction, common rafter line length, soffit tail, collar tie zone, and birdsmouth Height Above Plate. COLLAR TIE (UPPER 1/3) Rise: 3' 3-11/16" Net Run: 7' 11-1/4" Building Span: 16' 0" (192") + 12" Soffits PITCH: 5/12 (22.6°) | LINE: 8' 7-3/16" Total Cut w/ Tail: 9' 8-3/16" • HAP: 6-3/8"
Rafter Line Len
8' 7-3/16"
Run: 95-1/4"
Total Cut + Tail
9' 8-3/16"
Buy 10-ft 2x8
Height Above Plate
6-3/8"
Heel Cut: 1-7/16"
Plumb / Seat Angle
22.6° / 67.4°
Rise: 3' 3-11/16"
Total Rafters
32 pcs
16/side @ 16" OC

Hooked Tape-Measure Rafter Layout Schedule 13.00" / ft Run

Cut the ridge plumb angle at the top tip (0"), hook your tape on the long point of the crown edge, and pull down the board:

Cumulative Hooked Tape-Measure Marks Along Roof Rafter Top Edge
Layout Station Cumulative Mark Shop Saw / Square Spec
1. Ridge Plumb Cut (Peak) 0" (Hook Board Tip) 22.6° Miter Angle
2. Collar Tie Zone (Upper 1/3) 34-3/8" (34.40") IRC R802.4.6 Strap Limit
3. Birdsmouth Heel Plumb Line 103-3/16" (8' 7-3/16") HAP: 6-3/8"
4. Birdsmouth Level Seat Cut 3-1/2" Level Bearing 67.4° Seat • 1-7/16" Heel
5. Fascia Soffit Tail Plumb Cut 116-3/16" (9' 8-3/16") Tail: +13"

Required Bill of Materials (BOM) & Hardware

Auto-Calculated Quantities
  • 32 × 10-ft 2x8 #2 Kiln-Dried Framing Rafters 16 rafters per slope @ 16" OC across 20-ft ridge
  • 14 Sheets × 4x8 (7/16" or 5/8") APA Structural Roof Sheathing Covers 387 sq ft sloped roof deck (+10% gable/starter waste)
  • 32 × Simpson Strong-Tie H2.5A Hurricane Rafter Ties Plus 6 × 1x6/2x4 Collar Ties (4ft OC) & 2 × 16-ft Ridge Boards

Independent Field Spec Notice: Geometry and birdsmouth notch limits follow 2024 IRC Sections R802.4, R802.6, and R802.7.1. Verify snow-load lumber spans against local R802.4.1 tables.

Need full-scale Jobsite Cut Sheet + Vector .SVG blueprint?

Pre-Calculated Roof Rafter Calculator Blueprints (12 Field Specs)

Select any standard jobsite specification below to load its exact 2D SVG diagram and engineering tables:

Open Base Roof Rafter Calculator →
Contractor & Instructor Widget

Embed This 2D SVG Instrument on Your Website (Ad-Free)

Carpentry instructors, trade schools, and builders can embed the standalone ad-free version of this 2D CAD calculator with one HTML snippet.

SPECIFICATION WALKTHROUGH // 16-Ft Shed (5/12 Pitch)

Mathematical Derivation & Field Specifications: 16-Ft Shed (5/12 Pitch)

Updated • Published by LayoutCalculator

For a 16-foot (192") building width framed at a 5/12 roof pitch (22.6° slope) with a 1.5" ridge board, subtracting half the ridge thickness per side leaves an adjusted horizontal run of 95-1/4" (95.25"). Multiplying by the unit secant factor 1.0833 establishes a ridge-to-heel line length of 8' 7-3/16" (103.19") and a ridge peak rise of 39.7" (3.31 ft) above the wall plate.

Adding a 12" horizontal eave projection contributes 13" of sloped tail stock, bringing overall cut length to 9' 8-3/16" (order 10-ft 2x8 boards). Per 2024 IRC Section R802.7.1, birdsmouth end notches on 2x8 (7.25" actual depth) must not exceed 2-7/16" (D/3), preserving a 6-3/8" Height Above Plate (HAP) across all 36 rafters (16 pairs @ 16" OC + 10% cull).

Roof Pitch Sensitivity Matrix for 16-Ft Building Span (12" Overhang)

Roof Pitch Plumb Cut Angle Secant Factor Main Line Length Total w/ Overhang Min Lumber Stock
4/12 18.4° 1.0541 8' 4-3/8" 9' 5-1/16" 10 ft 2x8
6/12 26.6° 1.1180 8' 10-1/2" 9' 11-15/16" 10 ft 2x8
8/12 33.7° 1.2019 9' 6-1/2" 10' 8-7/8" 12 ft 2x8
10/12 39.8° 1.3017 10' 4" 11' 7-5/8" 12 ft 2x8
12/12 45.0° 1.4142 11' 2-11/16" 12' 7-11/16" 14 ft 2x8

Pattern Rafter Scribe & Saw Layout Checkpoints (2x8 @ 5/12)

Checkpoint Hooked Tape / Angle Code / Framing Rule
1. Ridge Plumb Cut 0" Origin • 22.6° Miter Crown edge facing UP; deduct 0.75" half-ridge
2. Birdsmouth Heel Plumb 8' 7-3/16" (103.19") HAP = 6-3/8" above top plate; 3-1/2" level seat
3. Fascia Tail Plumb Cut 9' 8-3/16" (116.19") 12" horizontal soffit projection (22.6° plumb)

Official Building Code & Industry Standard Citations

Field Manuals & Code Tables for Roof Rafter Calculator

Index of All 107 Manuals →

Frequently Asked Questions (16-Ft Shed (5/12 Pitch))

What is the exact rafter line length and plumb cut angle for a 16-ft span at 5/12 pitch?

▼

Deducting half of a 1.5" ridge board from a 16-ft (192") building width leaves an adjusted horizontal run of 95-1/4". At 5/12 pitch (22.6° plumb cut, 67.4° seat cut), ridge-to-heel line length is 8' 7-3/16" (103.19") plus a 13" overhang tail (9' 8-3/16" overall).

What is the maximum birdsmouth notch depth allowed by IRC R802.7.1 on 2x8 rafters?

▼

Under 2024 IRC Section R802.7.1, an end-bearing birdsmouth notch cannot exceed one-third (D/3) of the actual rafter depth. For 2x8 lumber (7.25" actual depth), maximum notch depth is 2-7/16", preserving a 6-3/8" Height Above Plate (HAP).

What lumber length and quantity should I order for a 16' × 20' gable roof at 16" OC?

▼

Each 9' 8-3/16" common rafter requires 10-foot 2x8 stock. Across a 20-foot roof ridge at 16" on-center (16 rafter pairs), order 36 boards including a 10% culling buffer.